Garden

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

Top Reasons why your blades will not engage on your riding mower or tractor: Belt-the number one cause for your blades not to engage is that your belt is either stretched or loose causing it to slip or fall off completely. Belt could have snapped also.
If the engine dies when the blades engage, it could be the result of a damaged safety switch. The first step in assessing the safety switch is to make sure it is plugged in securely. The switch is located underneath the seat, and you may have to remove the seat to reach it.
If the PTO clutch is not getting power, if the clutch solenoid is defective, or if the clutch is worn out, the lawn mower blades will not engage. The PTO clutch is not repairable—if the clutch is defective, you must replace it.
Deformed Blade

In some cases, the unnatural shape of the blade can be enough to prevent you from tightening it properly. A bent shape can also mess with the blade`s overall balance. An unbalanced mower blade can produce vibrations that will loosen the bolt over time.

Worn or broken blade drive belt – If the riding mower blades are not spinning, the blade drive belt may be worn or broken and unable to engage the blades. If the belt is intact, inspect it to see if it`s loose or slipping on the pulleys then replace it with a new one if necessary.
A dull blade is the number one reason for leaving uncut grass. The blunt blade will damage your lawn in no time at all; it tears the grass and leaves a jagged edge which turns the grass tips yellow. The recommended way to repair the yellow grass damage – regularly cut with a sharp lawnmower blade.
A Husqvarna riding mower commonly dies when blades are engaged because the grass box is not fully closed. Other possible causes include: Grass Box Misaligned. Grass Box Sensor Wiring Loose.
Pump trouble is usually characterized by increased noise, increased heat, erratic operation of cylinders, difficulty or inability to develop full output, decreased speed of cylinders or hydraulic motors, or failure of the system to work at all.
Lack of ownership: Since PTO isn`t accrued as they work, employees don`t feel like it “belongs” to them. If they don`t feel like they`ve earned it, they don`t use it. Lack of encouragement: Managers fall into the same trap of taking less time off. This sets a bad example that their employees feel pressured to follow.
An unbalanced blade spinning that fast will cause a significant amount of vibration, which will put stress on yout blade shaft, spindle, and even the engine. So if you want to get the most life out of your mower… keep the blades balanced!

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

Wont stay running – Mtd 22" Yard Machine Push Mower
ANSWER : Under neath the carby is a single brass bolt, undo it

that one bolt is a multi jet, find four holes use a fine pin and carby cleaner ,hint one is at the top were the thread starts , one is in the inside center and two in the sides
put it back in and prim and start, hope it helps

Read Full Q/A … : Garden

Why wont my blade engage
ANSWER : Bad pto clutch shorting out

Read Full Q/A … : Garden

Carb problems wont stay running unless i unplug and plug in the anti diesel switch the plug on the fuel bowl
ANSWER : Check and see if all your carb jets or clean sound like some dirt got into one

Read Full Q/A … : Garden

When I hold the bar down that engages the blade it will not cut?
ANSWER : Is the blade sharp?

Read Full Q/A … : Garden

Put new belt on riding lawn mower now blade wont engage
ANSWER : How many belt on a columbia lawn tractor
Lost traction when cutting grass
do they have a cluth?

Read Full Q/A … : Garden

Why my blade wont engage on my toro 74370 zeroturn mower
ANSWER : It has an electromagnetic clutch switch on it,that is more than likely bad. Try this,pull the pto switch out and start the engine,then disconnect the 2 wires coming from the switch and just tap them together and see if they will come on. If they do then you need to replace that switch.

Read Full Q/A … : Garden

Blades wont ingage on my craftsman lawn tractor #917.274811?
ANSWER : After hitting a tree root, blades will not cut when I press to engage

Read Full Q/A … : Garden

Where is the primer ball
ANSWER : It may not have a primer ball. If it does, it would be attached to the carberator. If it starts, but won’t stay running, that could mean your carberator needs to be cleaned/serviced.

Read Full Q/A … : Garden