How to set a john deere 9760sts combine in canola crop?

Setting the Combine For Oats

For the 50 rpm cylinder, you should increase the speed by and concave about 0.5 in each step. This is suitable for hot conditions and also with ripe oats. Another option is to set the cylinder at 1000 and concave at 0.5. Instead of speeding up the cylinder, you have to slow it down.

Single-tine separation (STS™) module provides maximum separation of threshed grain. The STS module on the S700 Combine is the heart of where grain is threshed and then differentiated from the material other than grain to fall onto the cleaning shoe area for additional separation.

Spacing of 25-30 cm should be kept between rows. Depth should be 3-4 cm. Sowing is done through drilling method, zero tillage drill.

John Deere 9670 STS Combines Class 6 for Sale | Tractor Zoom. What`s It Worth?

John Deere 9760 STS Combines Class 7 for Sale | Tractor Zoom. What`s It Worth?

Large 200 U.S. gallon fuel tank on the 9560 STS, 250 U.S. gallon fuel tank on the 9660 STS and 9760 STS, and 305 U.S. gallon fuel tank on the 9860 STS reduces fuel stops and increases productivity.

Tractor`s engine power is 80 h.p. (4 cylinders, working volume 4.75 L). Fuel consumption quota is 5,5 l/h. Modern tractor John Deere 8310R has been producing since 2011.

it could have 4,000-5,000 engine hours and 2,500-3,000 separator hours or more. The depreciation of the machine slows over time. By the time it reach 17-20 years old, typically the value of the machine is 10-20% of the original value when the machine was new.

The John Deere X9 1100 is the most powerful John Deere combine, as of 2023. With a 690 horsepower PowerTech PWS engine and 53 horsepower booster, this combine makes it easy to harvest more bushels per hour, more acres per day, lower harvesting costs, and improve production efficiency.

Cage Vanes: All (9 vanes) in Slow position, front to back. Reduces rotor loss, especially important with higher yields. If saving the straw, vanes should be in fast position. Rotor Speed: Base line is 950-1050 RPM.

Mature wheat is ready to harvest. When the crop has dried to a golden yellow colour and there is no more visible green in it, the farmer breaks the seed-head off a plant and `rubs it out` between his hands. The grains of wheat are released and he can then bite them – if they`re hard, the crop is ready to go.

Oat is usually seeded with a row spacing of 18-30 cm (7.5-12 inches). Research over a number of years has demonstrated that there is very little differences in yields within these row spacings.

Oats normally require about 60 days of growth following germination to reach the boot-stage. However, summer seeded oats tend to mature more slowly as days shorten in the fall, so may require an additional 10 days or so. Oats seeded on August 1^st would typically be ready to harvest in early-October.

Maturity & Harvesting

Swathing: Ideal grain moisture range is between 20-25%. oats too early will have a negative effect on test weight and milling quality. The oats should then dry to approximately 14% in the windrow before combining.

For best results, oat should be drill-planted on a conventionally tilled seedbed at a seeding rate of 80 to 100 pounds of seed per acre. Seeding depth can be as deep as 1½ inches, but a depth of only ½ to ¾ inch will increase the rate of emergence, establishment and forage production potential.

Maturity & Harvesting

Swathing: Ideal grain moisture range is between 20-25%. oats too early will have a negative effect on test weight and milling quality. The oats should then dry to approximately 14% in the windrow before combining.

For best results, oat should be drill-planted on a conventionally tilled seedbed at a seeding rate of 80 to 100 pounds of seed per acre. Seeding depth can be as deep as 1½ inches, but a depth of only ½ to ¾ inch will increase the rate of emergence, establishment and forage production potential.

Rates. 1.5 to 3 bu/acre to achieve a plant population of 18 – 23 plants/ft².