Garden
Spring popped out
How to Identify and Fix Common Gardening Problems ?
We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :
Disconnect the plug from mains. Press the release latch on the spool head cover and remove cover, pulling it straight off the cutting head assembly. Pull the cutting head cover away from the spool holder. Keep all areas of the cutting head cover and spool holder clean.
change your trimmer head is because after a while once it gets worn down too much it`ll then struggle to feed your trimmer line. you may begin to notice this problem when you start to bump. against surfaces or it`s extremely hard for it to feed more trimmer line out have a look at.
With fewer moving parts, 2-stroke string trimmers are dependable tools. They weigh little and vibrate less than 4-stroke trimmers, which reduces operator fatigue and makes for a better trimming experience. They also require less maintenance.
A trimmer with a single cutting line is easier to re-spool than one with twin lines, though the latter can give better cutting performance.
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
I have a 20″ bar chain saw (51 Air Injection)
ANSWER : The part no. of the spring is 501763101 it comes in a plastic keeper so is very easy to fit, check the web for sellers.
Read Full Q/A … : Garden
Chainsaw starter rope won’t pull
ANSWER : Pull your spark plug to ensure it isn’t a compression issue or even piston/rod damage. If it still doesn’t move, pull off your starter assembly and try to rotate the fly wheel by hand. If it turns, then your issue is in your recoil spring kit. You can replace the unit, or try to disassemble and reassemble.
Read Full Q/A … : Garden
How do i rewind the recoil spring on my craftsman lawn mower?
ANSWER : Normally these small engines use a clock spring to retract the rope.
Remove the cover on the top and you should find the spring either broken or the tab where the spring end has broken off or jumped out of the mount.
You will need to pre-load the spring with enough tension to retract the rope.
Remove the pull handle from the rope, load the spring and then wrap the rope around the pully holding the pully and spring in the loaded position. place the end of the rope through the hole and tie up the handle. The rope should pull and retract without being installed on the engine.
Best explained here…
https://www.youtube.com/watch?v=tmo6oYOJJ4U
Remove the cover on the top and you should find the spring either broken or the tab where the spring end has broken off or jumped out of the mount.
You will need to pre-load the spring with enough tension to retract the rope.
Remove the pull handle from the rope, load the spring and then wrap the rope around the pully holding the pully and spring in the loaded position. place the end of the rope through the hole and tie up the handle. The rope should pull and retract without being installed on the engine.
Best explained here…
https://www.youtube.com/watch?v=tmo6oYOJJ4U
Read Full Q/A … : Garden
Starter rope won’t retract
ANSWER : You have to wind the spring as tight as you can before you put the rope on. Then allow the spring to unwind, pulling the rope onto the spool. Be very careful when you take it apart. Good luck…Lee
Read Full Q/A … : Garden
The rope broke when I tried to start the chainsaw. How do I replace it?
ANSWER : Your rewind spring is now sprung. Remove recoil assy ( the part your rope slides into). Remove all old rope remnants and rewind the spring. Install new rope, tie it off and slowly release spring rewinding the rope.
Read Full Q/A … : Garden
Replaceing mower deck belt on 20 hp 42 mower model no 917275660. Got the belt on. How do I get the cluch spring back on.
ANSWER : Are you refering to the spring attached to the end of the cable that runs up to the lever on the dash to engage the blades? All you needed to disconnect was that cable on top of the idler arm that’s held in place by a ‘hairpin’ and the left pulley cover to put the belt on.
Read Full Q/A … : Garden
How do I replace the trigger on the Huskie 350? Does it just snap out, is there a pin to drive out or do I have to separate the case. If I have to separate the case, how?
ANSWER : To remove the the trigger there is a alloy pin that needs be be driven out. Before you can take the trigger out, you need to remove the trigger lock ( dead man ) to remove the trigger lock, gently pry the two halfs of the tank apart at the rear opening where the lock sits, this will allow the back end of the throttle lock to pop up, once up pull the throttle lock toward the rear of the saw and it will come away ( bayonet fitting in the tank ) the trigger will now come out with its spring once the pin is removed.
Read Full Q/A … : Garden
The recoil does not recoil – Earthquake 6015V Rear Tine Rototiller
ANSWER : Depending on engine you remove the housing, underneath you will see a pulley in which the cord goes around. Remove it, a couple of things could be there, spring has broken, easily replaced an not expensive. Could be trash or broken cord. This is an easy job dont panic follow instructions on new part. More than anything else its a coiled spring. Not much else could be wrong an if it is you can spot it. . You may need to replace pulley if it has a crack in it. They have long since quit making them from metal now. Pulley or spring or both is your problem.
Read Full Q/A … : Garden
