Pro 25hht 25cc 22″ Gas Hedge Trimmer

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

With a severed cord, your hedge trimmer is virtually worthless. With a small amount of money and a little ingenuity, however, you can repair the cord and have the trimmer running. If the cord left attached to the trimmer is long enough to be useable, then you simply can add a new plug to its end.
A: The spark plug gap on all products is . 025-inch.
gasoline for a 50:1 mixture. Shake well. Pour into fuel tank. 10% by volume (E-15, E-85) or any methanol blended fuel.
For most racing applications, you usually want the plug gap to be between 0.020 and 0.040 of an inch. Most engine builders seem to settle around 0.035 of an inch. Factors such as the type of ignition you run, cylinder heads, fuel and even timing can affect how much gap will work best for you.
A 40:1 ratio is recommended for this particular model. To obtain the correct mixture, pour 3.2 ounces (95 ml) of 2-cycle synthetic oil into one gallon (4 liters) of fresh unleaded gasoline.
Q: How do I mix gas and oil? A: Mix 3.2 ounces of Poulan 2-cycle air cooled engine oil to one gallon of fresh unleaded gasoline to obtain the recommended 40:1 fuel to oil ratio.
Accidentally cut your good, heavy-duty extension cord? Replacement cords are expensive, and you can save money by just repairing it. Instead of splicing, add a new plug on the piece of the cord with the receptacle and a new receptacle on the piece of the cord with the plug.
Corded electric hedge trimmers: These trimmers are all you need for lighter trimming close to the house. They tend to be far cheaper—some are only about $50—and can run indefinitely as long as they`re plugged in.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

Hht 25 will not start
ANSWER : CHECK THE COMPRESSION 90LBS MIN.

Pull cord is difficult to pull after third pull becomes stuck but will turn if pull hard repeats every three to four pulls.
ANSWER : No response to clarification request.

I was replacing pull cord and the tiny bar which connects the trigger to the carb fell off before I could see how it was installed. I canot figure out how it goes back. It is a Bvm 200 25cc Poulan leaf blower
ANSWER : It should be pretty simple to replace. Would expect the trigger to come out, put the rod/bar on the carb then on the trigger (probably has to swivel the trigger to get the part on) the set trigger back in it’s position. Hope this helps. Easier to do than explain.

Hi i wonder if you can help my Ryobi hedge trimmer has a problem with the pull cord it works goes in and out but it does not turn the engine over is there maybe a key way or something that maybe broken ??
many thanks
Nick
ANSWER : Hello Nick,

Inside the cord attaches to a plastic wheel which cranks the engine. This cord can become loose or can break after some use. Try opening the plastic casing where the cord is to see if this is the problem.

Thanks

How do you change a head on a poulan pro trimmer
ANSWER : Try putting a wrench on the nut that is above the head to hold it steady. Then try turning the head off being aware that the stud the head spins on to has left handed thread on it.

String for a Poulan Pro PPB330
ANSWER : Hello,

Pull your spool off, and look next to the notches on the bottom of the spool. The decimal number is the size of line that you can use. Some spools will have more than one size listed; they can use either size.

Best regards, –W/D–

How do you wind replacement line to the Poulan Pro String Trimmer?
ANSWER : If it is a duel line trimmer then:Cut two separate pieces of string, about 7 ft. each.Stick the end of
the line in the hole on the inside of spool.Wind clockwise onto spool,
putting the line that is closest to the ground on first.Once you have
winded this piece on, lock the last 4 inches of line through the slits
on spool.Repeat process for second piece of line, locking the last 4
inches in slot opposite the other locked in piece.Put the spool on the
trimmer, feeding the end of lines through either hole on trimmer.Before you push the spool all the way on, pull the strings out of the
locked position.If it is a single line trimmer, just wind a single piece of string clockwise onto spool.Jim

I have pulled the cord out of my gas powered trimmer. What is the easiest way to fix this
ANSWER : Remove the pull start mechanism, remove the old rope from the inside plastic, thread a new rope through the hole in the outside and through the hole in the plastic center where you removed the old rope, Now reach between the spool and the edge of the casing and pull some slack in the rope, there will be a notch in the spool, set the rope into the notch and begin spinning the spool to make tension in the spring ( correct direction is the same way the rope is spooled in. go until you have good tension on spring, grab rope left outside casing and pull through, then let rope get pulled into the spool with the spring tension you have created. Now just reattach the handle.