Garden

Remove cover to service points and ignition model around 25 years old
Experienced gardeners share their insights in answering this question :
First thing is to pull the spark plug lead off so you can’t have the machine accidently fire.
Locate bolts and nuts that hold covers in place and remove them and the covers.
There will be a nut in the centre of the flywheel. Loosen it so that it is just a bit higher than the the threads. Lift up on the flywheel and tap sharply down on the nut with a wood or plastic mallet (or use a block of wood and a hammer. The flywheel is on a tapered shaft so it will loosen upwards. Remove the nut and lift off the flywheel. Don’t lose the metal key that aligns the flywheel in the correct position.
The parts that you want to play with will now be available.

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

These holes are for balancing purpose. If the flywheel is not balanced, then during high speeds, it will generate unbalanced forces on the shaft on which it is fitted. By removing some portion of the flywheel in the form of these holes, it gets balanced.
A flywheel is essentially a mechanical battery consisting of a mass rotating around an axis. It stores energy in the form of kinetic energy and works by accelerating a rotor to very high speeds and maintaining the energy in the system as rotational energy.
A flywheel is a mechanical device which stores energy in the form of rotational momentum. Torque can be applied to a flywheel to cause it to spin, increasing its rotational momentum. This stored momentum can then be used to apply torque to any rotating object, most commonly machinery or motor vehicles.
What is the flywheel effect and how can it grow your business? The flywheel effect happens when small wins for your business build on each other over time and eventually gain so much momentum that growth almost seems to happen by itself – similar to the momentum created by a flywheel on a rowing machine.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

How do I remove the clutch on an Echo chain saw??
ANSWER : Backwards to the rotation of the motor, all you need are basic tools to do this.

Read Full Q/A … : Garden

Cant remove clutch cover – Echo CS400 18" Chain Saw
ANSWER : Is the Chain brake engaged?

Read Full Q/A … : Garden

New coil for chainsaw
ANSWER : The coil is on the flywheel side of unit. remove the recoil cover and you will see the flywheel and coil. your have to remove the ground wire from shut off switch and two bolts holding coil in place. when installing new coil you need to leave a 10 thousand air gap between the coil leg and the flywheel magnet for proper operation

Read Full Q/A … : Garden

Ryobi ptl 3043a – pull cord has broke how do I rewind a new one on?
ANSWER : Remove the tube that holds the flex-drive shaft from the front of the motor cover.Remove the rear engine cover. Remove the throttle cable from the carburetor. Mark and unplug any wires for the on/off switch that go to the ignition coil (underneath front cover) if possible. Now if you have pulled the driveshaft tube out of the way, the clutch drum is up next. Inside it, screwed into the very end of the engine’s crankshaft is a Torx #25 screw. Before you loosen it, you will have to lock up the engine. To do so, remove the spark plug. Pull on the starter until the piston is down, then insert a length of clean, soft rope into the engine. The engine will come up and compress the rope, thus locking it in place to allow clutch drum and clutch removal. Loosen the T-25 (Star bit or Torx head) screw inside the drum.. You may be able to remove it with a long thin-blade screwdriver also.It probably won’t come completely out…it is made this way. Next, remove the clutch. It is screwed onto a small threaded section of the crankshaft Removal is counterclockwise.. It will be pretty tight. To help, apply peneterating oil. Whack the ears of the clutch near the center with a hammer and a dull flat-blade chisel or a small piece of wood unless there are bolts. then use a wrench. It will turn counterclockwise for removal and there will probably be a removal direction arrow on it’s face. After getting that off, remove the Torx screws holding the cover to the engine. The starter unit should be mounted inside as it mates with the top of the flywheel to start the motor. Remember to preload tension (5-7 turns) on the starter unit. Make sure the handle is installed. Jam the unit with a screwdriver or vise grips so you can insert and tie off the new rope. Then remove jam device and let recoil pull your new rope into place while holding the handle. Reassemble and you are done. Disassembly requires Torx head drivers and a good flat-blade screwdriver. Post back if needed.

Read Full Q/A … : Garden

How do u remove the tire off a rear rotiller – Troy Bilt Mtd Tiller Wheel Tire 480×4008
ANSWER : Remove the pin that secures the wheel to the axle and remove the wheel. Sometimes the wheel will become rusted to the axle and can not be removed. Its best to leave it be. Attempting to beat the wheel off the axle runs the risk of causing internal damage to the transmission. Once the wheel is off, remove the valve and release the air then using your tire tools remove the tire.

Read Full Q/A … : Garden

How to set timing on a push mower with a tecumseh
ANSWER : If it is an older machine, yes, the points are underneath the flywheel—it can be removed without a puller—just a little patience will get it off

Read Full Q/A … : Garden

How to remove the clutch housing to insert new starter rope
ANSWER : I see that this machine has a 31cc engine with chrome-plated cylinder. I will now include the detailed instructions on how to remove the clutch and insert new starter rope.

Remove the tube that holds the flex-drive shaft from the front of the motor cover.Remove the rear engine cover. Remove the throttle cable from the carburetor. Mark and unplug any wires for the on/off switch that go to the ignition coil (underneath front cover) if possible. Now if you have pulled the driveshaft tube out of the way, the clutch drum is up next. Inside it, screwed into the very end of the engine’s crankshaft is a Torx #25 screw. Before you loosen it, you will have to lock up the engine. To do so, remove the spark plug. Pull on the starter until the piston is down, then insert a length of clean, soft rope into the engine. The engine will come up and compress the rope, thus locking it in place to allow clutch drum and clutch removal. Loosen the T-25 (Star bit or Torx head) screw inside the drum.. You may be able to remove it with a long thin-blade screwdriver also.It probably won’t come completely out…it is made this way. Next, remove the clutch. It is screwed onto a small threaded section of the crankshaft Removal is counterclockwise.. It will be pretty tight. To help, apply peneterating oil. Whack the ears of the clutch near the center with a hammer and a dull flat-blade chisel or a small piece of wood unless there are bolts. then use a wrench. It will turn counterclockwise for removal and there will probably be a removal direction arrow on it’s face. After getting that off, remove the Torx screws holding the cover to the engine. The starter unit should be mounted inside as it mates with the top of the flywheel to start the motor. Remember to preload tension (5-7 turns) on the starter unit. Make sure the handle is installed. Jam the unit with a screwdriver or vise grips so you can insert and tie off the new rope. Then remove jam device and let recoil pull your new rope into place while holding the handle. Reassemble and you are done. Disassembly requires Torx head drivers and a good flat-blade screwdriver. Post back if needed.

Read Full Q/A … : Garden

How do I remove the pulley from the bottom of the crankshaft?
ANSWER : Crankshaft of what? I see a picture of a riding mower, is that what your working on? If so, you need a pulley puller. You can get one from your local autoparts store like autozone usually for a refundable deposit.

Read Full Q/A … : Garden