Garden

I put in one ounce, and it appears to be full…this can't be enough?
Experienced gardeners share their insights in answering this question :
Most push mower take around a half a quart and riders take at least 1 quart and some take 2 or moer

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

A 100ml bottle is suitable for mixing with 5 litres of fuel to achieve a 50:1 fuel-oil ratio.
Common gasoline and oil mix ratios are 50:1 and 40:1. Meaning there is 50/40 parts gasoline to one part oil when mixed. The lower the mix ratio number the more oil per volume in the gasoline. To mix properly add oil to your gas can, then add fresh gasoline from the pump.
Typically, engines need five to eight quarts of oil. However, the size of your engine can impact how much oil is required. For example, a 4-cylinder oil engine may require around five quarts of oil, whereas a 6-cylinder oil needs six quarts. Usually, the smaller the engine is, the less oil you`ll need for your vehicle.
For a mixing ratio of 1 : 50 you need 5 litres of high-octane gas and 0.10 litres (100 ml) of STIHL two-stroke oil.
Forty to one (40:1) is a pretty easy 2 stroke ratio to calculate, you simply multiply the litre amount by 25. To make it easier you can use the following old school reference chart.
The GOR is defined as the volume ratio of gas and liquid phase obtained by taking petroleum from one equilibrium pressure and temperature, in the reservoir, to another, at the surface, via a precisely defined path.
This ratio indicates how much fresh, regular unleaded gasoline (containing no more than 10% ethanol) to mix with how much oil. For all Remington 2-cycle products, the ratio is 40:1. This means you`ll want to add 3.2 oz of oil to every gallon of gasoline.
Mixing ratios

For a mixing ratio of 1 : 50 you need 5 litres of petrol and 0.10 litres (100cm³) of STIHL two-stroke oil.

If you can`t find the specific ratio for your mix, 40:1 is accepted as an average ratio for two-stroke engines. This is 125mls of two stroke oil to 5L of fuel.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

Dont know what type of oil to use – Toro Power Lawn Mower
ANSWER : Put straight 30 weight motor oil in it. Not 10W30 or any multi-viscosity oil. Straight 30 weight motor oil. If you’re doing a complete oil change, then you may want to use Synthetic 30 weight, which will last longer between oil changes and also make your engine last longer (but it costs more too). Best of luck to you.James

Read Full Q/A … : Garden

What kind of oil in the oil tank and how much for the remington electric pole saw ?
ANSWER : Bar & chain oil is the best. You can use regular or synthetic. Some say you can use atf (auto transmission fluid) or sae30 oil. I use bar & chain oil.

Read Full Q/A … : Garden

What oil do we put into the poulan 3.0 peak hp
ANSWER : I assume you are referring to the Bar/Chain oil?
That would be Almost any Available brand chainsaw Bar and Chain oil, If that is not available you can use New uncontaminated SAE 30 motor oil.

Read Full Q/A … : Garden

My husky 455 rancher is not oiling the chain properly. I have tried to clean all the oil ports on the bar and saw but it still is hardly pumping any oil to the chain. What could be the problem? How does the oiling system work?
ANSWER : The problem is very likely to be a clogged but more likely faulty internal oil pump (especially if your chainsaw is old).Hope it helps.

Read Full Q/A … : Garden

Ms 170 leaks bar chain oil out bottom, no oil on chain
ANSWER : Your clutch drum bearing has gone bad, letting the clutch drum to move around and cut into the oiler behind it, so now it just pumps the oil out that hole. You have to get that fixed to use the saw, otherwise you’re going to cause catastrophic damage to the saw very soon.

Read Full Q/A … : Garden

I have a husqvarna 137 chainsaw. The problem is with the bar oil. When the saw runs oil is flowing but where the rubber corner piece which allows the oil to flow out of appears to be just dripping the oil straight out. It looks like it should fill a small reservoir behind the metal plate and the oil then moves upwards where the chains drags the oil through the oil hole on the bar which is moving outwards as in the top chain on the bar. However the chain-brake area is just getting messy with oil splattering all over and the bar not actually getting oiled. I have fitted a new metal plate to see if the corner of the original was not sealing properly but that has not helped. The bar holes are clean. Any suggestions as I can’t see what it could be?
ANSWER : It’s the rubbers. I had the same problem with my 137 and 141. The rubbers shrink over time and the oil never makes it up the channel. The replacement part is one piece and less prone to leaking than the original 2 piece design.

Read Full Q/A … : Garden

My 290 isn’t oiling chain. I tried adjusting oil flow and still no oil?
ANSWER : You have to remove the bar and clean it out

Read Full Q/A … : Garden

Do I need gas and oil mix – Poulan Super 250a Chainsaw Plate
ANSWER : I think Poulan uses a 40:1 ratio to one gallon of gas, however I have always used 50:1 the same as my sthl saws with no issue. I would rather have more oil mix that to little.

Read Full Q/A … : Garden