Garden

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

Replacing the Mower Deck

Slide the deck under the machine and push it rearward to replace the belt on the engine pulley. Then move the deck forward until it`s in position to lift the back end and re-hang it on the rear support bracket.

For most effective results, a lawn mower deck should have a pitch, or height difference of 1/8-inch to 1/2-inch between the front of the deck to the back of the deck. Naturally, this makes the sweet spot about 1/4-inch of pitch, depending on the mower model.
For most effective results, a lawn mower deck should have a pitch of 1/8-inch to 1/2-inch between the height of the deck rear to the height of the deck front. Naturally, this makes the sweet spot about 1/4-inch of pitch, depending on the type of mower.
The top setting for most mowers gives a cutting height between 3.25 and 4 inches. This is best for your lawn, but at a setting of 4 inches you may sometimes see some “laying-over” of turf blades that some people find undesirable. For this reason, some people prefer to mow at 3 or 3.5 inches.
Using the deck-leveling gauge, check the height between the ground and the deck rim at the adjusting point one. This gauge should then just slip under the deck`s rim. If adjustments are needed on the rear left deck`s rim area, you will want to turn the rear nuts clockwise and raise the mower deck.
For the first mow of the season, it is better to lower your deck height to about 1.5”. This will help clean up the dead grass as well as allow more light to shine through and really get your lawn to come out of dormancy. After the first cutting of the season, you can raise your deck height to 2-2.5”.
Fixed decks are built as one piece into the overall frame of the mower. These decks are known for their durability. The Stander® and the Velke Hydro™ Stand-on Velke Hydro™ are just two examples of our fixed deck offerings.
Turn the adjusting lock nut clockwise to raise the mower and counterclockwise to lower it. Measure from the blade to the ground again on both sides and adjust until the difference between the blade tip heights are within ⅛ -inch. Rotate the blades so that their direction is now front to back.
However, while all engines are interchangeable, it doesn`t follow that all mower decks are interchangeable. While mower engine manufacturers agree on standard engine mounting specs, no such agreement is in place for any other mower component.
Instead of purchasing a replacement spindle for your riding mower deck, you can repair the spindle for a fraction of the cost by replacing just the worn-out bearings.
Turn the adjusting lock nut clockwise to raise the mower and counterclockwise to lower it. Measure from the blade to the ground again on both sides and adjust until the difference between the blade tip heights are within ⅛ -inch. Rotate the blades so that their direction is now front to back.
Mower deck gauge wheels should be properly adjusted to prevent scalping grass on uneven terrain. The bottom of the wheels should sit approximately 1/8-1/2 of an inch from the ground, depending on your cutting height.
Mower deck gauge wheels should be properly adjusted to prevent scalping grass on uneven terrain. The bottom of the wheels should sit approximately 1/8-1/2 of an inch from the ground, depending on your cutting height.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

Where is the battery located on a john deere RX73 riding lawn mower?
ANSWER : These mowers did not have electric start, therefore no battery

Read Full Q/A … : Garden

Murray mower belt model 52431×92 – Craftsman 17.5 hp 42 in. Deck Lawn Tractor – CA Model
ANSWER : Get a 1/2″ x 92″ belt

Read Full Q/A … : Garden

How to start murray 188 lawn tractor – Craftsman 17.5 hp 42 in. Deck Lawn Tractor – CA Model
ANSWER : Need more info. what is it doing or not doing

Read Full Q/A … : Garden

What size for a 611 deutz allis 42 in deck – Mtd Drive Belt 42"
ANSWER : Go to simpletractors.com they may have the answer for you !

Read Full Q/A … : Garden

Where is the alternator on a mtd tractor – Craftsman 17.5 hp 42 in. Deck Lawn Tractor – CA Model
ANSWER : Hi, under the flywheel on top of the motor crankcase, regards Phil.

Read Full Q/A … : Garden

How do you replace the clutc bar? The clutch on the mower is stuck in gear
ANSWER : If its belt driven its probably the belt tention pully or the spring that pulls it back that is broken

Read Full Q/A … : Garden

How to adjust the mowing deck properly? – Craftsman 17.5 hp 42 in. Deck Lawn Tractor – CA Model
ANSWER : I use a string level just sit it on deck level front to back

Read Full Q/A … : Garden

Craftsman 917.270913 how long is deck belt
ANSWER : 1/2×95″

Read Full Q/A … : Garden