Rapid Loader, Trimmer Head
How do I change to a rapid loader head on an echo trimmer
Experienced gardeners share their insights in answering this question :
Line up the hole on the collar that the trimmer head is installed against with the arrow or notch on the gear housing, insert a punch or the brass colored pin that most Echo pieces of equipment come included with, this will lock the head. now turn the head clock wise, IT IS LEFT HAND THREADED! so righty loosey lefty tightey. now install the rapid loader with the included washers and10mm gold colored lefthand thread nut
How to Identify and Fix Common Gardening Problems ?
We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :
ECHO`s Rapid Loader® trimmer head offers the ultimate in easy reloading. Available in 2-line (21560056 and universal model 21560059) and 3-line (99944200221) configurations it`s perfect for smaller jobs with minimal yard obstacles. Model Fit Up. TOP FEATURES. Makes line changes lightning fast.
change your trimmer head is because after a while once it gets worn down too much it`ll then struggle to feed your trimmer line. you may begin to notice this problem when you start to bump. against surfaces or it`s extremely hard for it to feed more trimmer line out have a look at.
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
How to change to a rapid loader head on an echo
ANSWER : Line up the hole on the collar that the trimmer head is installed against with the arrow or notch on the gear housing, insert a punch or the brass colored pin that most Echo pieces of equipment come included with, this will lock the head. now turn the head clock wise, IT IS LEFT HAND THREADED! so righty loosey lefty tightey. now install the rapid loader with the included washers and10mm gold colored lefthand thread nut
Read Full Q/A … : Rapid Loader, Trimmer Head
How do you load the trimmer head… Lost the user manuel
ANSWER : Check out the manual (available under the technical documents section of the Echo webpage, or at http://www.echo-usa.com/documentation.asp?Model=SRM-210&lang=E )and it will tell you how to change it.
Read Full Q/A … : Rapid Loader, Trimmer Head
Starts easy will not rev up – Echo Rapid Loader, Trimmer Head
ANSWER : Sounds like you will need to clean your carburetor.
Sometimes you can get by with priming it a few times, and letting it run a few times like that and it will flush the gunk out of the jets,but most of the time you will need to rebuild the carburetor.If the mower is over a couple years old, then I also recommend that youbuy and install a new carburetor repair kit, because the diaphragm willget hard and that will cause it to be hard to crank.When you clean your carburetor and remove the jet screws, count the number of turns it takes to seat the jets from their original position.That way when you go to put the jets back in, you know how many turnsthey were in/out.Please rate me, ThanksGood Luck, I hope this helped
Sometimes you can get by with priming it a few times, and letting it run a few times like that and it will flush the gunk out of the jets,but most of the time you will need to rebuild the carburetor.If the mower is over a couple years old, then I also recommend that youbuy and install a new carburetor repair kit, because the diaphragm willget hard and that will cause it to be hard to crank.When you clean your carburetor and remove the jet screws, count the number of turns it takes to seat the jets from their original position.That way when you go to put the jets back in, you know how many turnsthey were in/out.Please rate me, ThanksGood Luck, I hope this helped
Read Full Q/A … : Rapid Loader, Trimmer Head
How do you properly load the spool on an Echo GT-2000 trimmer?
My brother gave me one and told me what to do, but I find that it
coils so tight that it kind of fuses itself. I have to pry it apart, thread
it through the two outlets, put the spring a=back, load the entire unit
only to have the same problem happen over and over again. I’m frustrated. Can this spool be replaced with something newer?
Help…thank you, Rob
My brother gave me one and told me what to do, but I find that it
coils so tight that it kind of fuses itself. I have to pry it apart, thread
it through the two outlets, put the spring a=back, load the entire unit
only to have the same problem happen over and over again. I’m frustrated. Can this spool be replaced with something newer?
Help…thank you, Rob
ANSWER : Try this YOUTUBE VIDEO out:www.youtube.com/watch?v=skxjWD7jyccGood Luck!Jim
Read Full Q/A … : Rapid Loader, Trimmer Head
Igntion coil on echo trimmer went bad, replaced with echo blower coil . there is a small difference in design but now have ignition. Engine still won’t start.
ANSWER : Make sure the air-gap between your used blower coil module and the magnets on the Echo’s flywheel is about the thickness of a regular business card. That is about .010″-.016″. The gap HAS to be present in order for the module to produce the spark.
Read Full Q/A … : Rapid Loader, Trimmer Head
Need Help Installing U-Turn Trimmer Head on Echo SRM-210
ANSWER : It is ridiculous, there are a bunch of bolts, and then a multi-fit brochure showing a grid of nonsense.There are instructions on the inside of the package, however that is how to string the line.
Read Full Q/A … : Rapid Loader, Trimmer Head
I need to replace the diaphragm in my Echo trimmer but can’t find the Echo replacement parts in my local hardware store. Is there another brand diaphragm that will fit an echo trimmer?
ANSWER : You can find carburetor diaphragms for all 2-cycle carburetors at PartsBuggy.com.
Read Full Q/A … : Rapid Loader, Trimmer Head
I need to replace the whole trimmer head and I dont know how to get the gear case off so I can put the new one on. Can anyone help?
ANSWER : To replace the trimmer head you don’t need to replace the gear case. If you look closely about a 1/4 inch up from the safety guard you’ll see a hole in the side of the “gearcase” assemby. (you may have to clean the old dead grass clippings off to see it) You can shove a rod into the hole that will stop the head from spinning freely and I believe you spin the head clock wise (reverse threads) to remove the head.
Read Full Q/A … : Rapid Loader, Trimmer Head
