Poulan

Experienced gardeners share their insights in answering this question :
Typical Fuel System (Primer Bulb and fuel lines may not apply)
http://www.this site.com/support/r3706813-2_cycle_fuel_system_repair
Fuel Line Replacement by SmallEng.com

The hose in the tank with the filter on the free end connects directly to the carburetor input connection.
If the saw is equipped with a primer bulb, an output line from the carburetor connects to the suction side of the primer (once the bulb is collapsed it draws fuel from the tank through the carburetor to refill as it inflates).
The pressure side of the primer returns displaced fuel to the tank as it is depressed.
Take lots of notes and a few digital photographs to help with reassembly. HTH
Lou

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

A single fuel pipe runs from the tank, under the floor of the car to a mechanical pump on the engine. The pump delivers fuel to the carburettor. Whenever you check fuel pipes, disconnect the battery to prevent stray sparks igniting petrol or petrol vapour.
Replacing the fuel hose on your vehicle is going to take time and patience, and it could require getting underneath the car. It`s also going to take the right tools for the job.
Most vehicles have rubber fuel hoses connecting the fuel pipes on the chassis to the fuel pump or carburetor on the engine. Rubber hoses are flexible and can be cut to length as required, but they have a tendency to perish over time and can rub through if not properly secured.
One is the high pressure line, which sends fuel to the injectors. The other is the return line, which dumps fuel that the injectors don`t use back into the tank.
The (clear) fuel intake line runs from the top of the carburetor (straight nipple) and goes to the short post on the back of the primer bulb. The return line (blue) comes from the long post on the back of the primer bulb and goes into the bottom of the fuel tank.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

Replaceing fuel line in polan 3300 chain saw – Poulan Pro 42CC 2 Cycle Chainsaw, 18"
ANSWER : Hi owjbhend…
Use a piece of wire and insert it into the fuel line, then bend a hook in the end and hook it over the end of the fuel line…lubricate the fuel line with some vaseoline very lightly…about the first one inch of the fuel line and then use your fingers to start the fuel line into the tank, once you have the fuel line in the tank give enough to hook the fuel filter to and so it can be dropped back into the tank.
Below is a drawing of how to route the fuel lines.
Please take time to rate me thumbs up
Please take time to rate me thumbs up

Read Full Q/A … : Poulan

My poulan pro 42cc starts normally, then as I begin cutting it boggs down and nearly stalls. As it warms up it seems to get worse, esp. if I turn it on the side to cut. I’ve cleaned it all up and checked the fuel lines. They are intact and no leaks or clogs detected. The only notable change is the primer bulb takes a little longer to return after pressing. It seems to idle fine and run good untill under work load.
Thanks for your help. Chas
ANSWER : Try cleaning your air filter. that should help. “BEEN THERE”

Read Full Q/A … : Poulan

How do I replace the fuel line for a Poulan ppbp30?
ANSWER : Open the top of the machine to access the carb, Normally it is easily done with needle nose pliers.

Read Full Q/A … : Poulan

My Poulan will start up but then when I try and give it more throttle it dies or even when I let off the throttle to idle it will die. Is this fuel line o dos the carb. need to be cleaned? How do I access these parts if so. New to fixing a chainsaw.Thanks!
ANSWER : It sounds very like a fuel issue, before diving into remove the carb check the easy stuff first, drain the fuel tank and fill with fresh fuel, pull the fuel hose out and check the condition of the filter on the end,any doubt replace it, check the condition of the fuel hose up to the carb for cracks or signs of age. Let us know how you get on

Read Full Q/A … : Poulan

Fuel mix 1.40 or 1:50? – Poulan Pro 42CC 2 Cycle Chainsaw, 18"
ANSWER : This is usually dependant on the two stroke oil quaility, good quaility two stroke oil from a major chainsaw manufacture will normally be advised to mix at 50.1, always try to buy good two stroke oil, from a chain saw manufacturer, they know the importence of oil quaility on high reving two strokes.

Read Full Q/A … : Poulan

Poulan te 450 cxl fuel lines need routed correctly two line both in tank one to fuel filter other line?
ANSWER : Other line is just left open like to send gas back from the carb.

Read Full Q/A … : Poulan

Poulan chainsaw 18″ 42 cc, pro gas filler cap?
ANSWER : Yep they swell after a while and will not screw in or out!
Sand the threads down so that the circumference is reduced with a course file or plumbers cloth, chamfer the threads a bit on the edges. A new one will do the same thing after a while so just fix the one you have.

Read Full Q/A … : Poulan

Poulanproleafblower not primeing
ANSWER : Either your fuel
is broken inside the tank or your carb is blocked up inside. Empty the fuel tank and look inside and see if you fuel inlet line has a little plastic or metal filter on the end. *(this is called a “clunk”) The clunk keeps the fuel line in gas no matter which way you have the blower tilted. Chances are you will see the clunk just laying in the bottom of the tank with whats left of the fuel line still attached. If the fuel line and clunk are intact then your need to get a diagram of the carb and do a dissembly and cleaning. The carbs have tiny screen filters which jam up with debris and gelled fuel. So a rebuild kit with new filter would be a good thing to get if your carb is cruddy. You can look online at Poulanpro and see which kit you need to buy. They are 10-15 bucks usually. New fuel lines is also a good idea if you are going this deep into the unit. Be safe and good luck!

Read Full Q/A … : Poulan