420cc 45-in Two-Stage Gas Snow Blower 31AH97P7711

I replaced the carberator, now the engine is over-reving. How would I adjust the governor on here?
Experienced gardeners share their insights in answering this question :
If you didnt change anything on gov dont start now.
you may have linkage in wrong hole
or bent linkage , or missing spring

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

When the crankshaft spins quickly, the flyweights open up, putting pressure on the governor cup and crank. This closes the throttle, limiting the air-fuel released into the engine. When the engine load increases, the crankshaft spins more slowly. This leads the flyweights to relax and the throttle to open back up.
Set idle speed adjusting screw, clockwise to increase rpm, counter-clockwise to decrease rpm. Idle rpm range should be 950 to 1050 rpms. Adjust idle mixture by turning idle mixture screw slowly clockwise until the engine runs poorly.
It is normal for a snow thrower engine to run in this manner. The engines on snow throwers are set to run with a slightly rich fuel mixture. This is to prevent the engine from bogging or stalling when the snow thrower suddenly experiences a heavy load of snow.
Droop is the decrease in speed that occurs when the governor output shaft moves from the minimum to the maximum fuel position in response to a load increase, expressed as a percentage of rated speed. If instead of a decrease in speed, an increase takes place, the governor shows a negative droop.
Speed limiters. Governors can be used to limit the top speed for vehicles, and for some classes of vehicle such devices are a legal requirement. They can more generally be used to limit the rotational speed of the internal combustion engine or protect the engine from damage due to excessive rotational speed.
It is normal for a snow thrower engine to run in this manner. The engines on snow throwers are set to run with a slightly rich fuel mixture. This is to prevent the engine from bogging or stalling when the snow thrower suddenly experiences a heavy load of snow.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

The RPM’s are to high and I can’t not turn them down. I tried to adjust them by turning the adjustment bolts. NO LUCK
ANSWER : You need to adjust the governor spring. Did you recently do some work on it? If so, you must have got that particular spring on wrong. What hp is your motor?Jim

I need to know how to adjust the governor on my MTD model 31A-62EE729 snowblower with a 179cc motor
ANSWER : Lossen the nut on the governor shaft, and move the arm toward the carb while holding the arm in this position turn the shaft counter clock wise and tighten the nut. and you are done. GOOD LUCK

Do you not know how to reset governor
ANSWER : Go to youtube they have videos on how to adjust governor

Carb screws need adjusted i need to know the settings
ANSWER : Hi. Lightly seat the low screw and bring it out one and a quarter turns. Lightly seat the high and bring it out one turn. Adjust idle screw to suit. Regards Phil.

What tool is required to adjust the carb. on a 142e husquvarna chainsaw?
ANSWER : Http://www.ehow.com/how_7241334_adjust-husqvarna-carburetor.html

My 290 isn’t oiling chain. I tried adjusting oil flow and still no oil?
ANSWER : You have to remove the bar and clean it out

HOW DO YOU ADJUST HIGH AND LOW SPEEDS ON HOMELITE BLOWER UTO8087 IF ONLY 1 SCREW ADJUSTMENT. 1 PORT FAC. PLUGED OFF.WHAT SHOULD IDLE RPM LOW B APPROX./ HIGH RPM
ANSWER : All the pictures I have of this carb show two adjusting screws.

How to adjust bar oil flow as bar heating up too much even though chain is sharp
ANSWER : Not all Husqvarna models have an adjustable pump, if it is adjustable there will be a slot head screw either at the side of the sprocket, or just under neath the sprocket, there will be a small symbal of a drop of oil and a + and – sign.