[SOLVED] How To Adjust Carberater - Poulan P3416 16Inch 34cc 2Cycle Gas Powered Chain Saw

P3416 16Inch 34cc 2Cycle Gas Powered Chain Saw

Experienced gardeners share their insights in answering this question :

There should be a small screw hole beside the prime pump bulb where you can adjust the centrifugal clutch nudge ahead speed, and then adjust down again for the correct idle without any chain motion. However the gas tank filter inside really needs to be cleared of a paper thin film of dust which gets in there while refueling and won’t let gas through – this causes you to think the carb needs more gas or the idle setting is wrong.

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

The fuel line may be clogged from stale fuel deposits, more reasons to cause your chainsaw to cut out when applying throttle. If a fuel line is cracked, it will leak gasoline and draw air from outside into the fuel line. If the line is leaking fuel, it needs to be replaced.

Insert a small flat-head screwdriver into the idle speed screw and turn it clockwise to increase the engine speed if it idles too slowly. As soon as the chain starts to move, turn the screw counterclockwise until the engine idles without dying and the chain stops moving for the correct idle speed.

The letters on the screws represent High (H), Low (L) and Idle (T). The H screw regulates the Air/Fuel mix during high RPMs, while the L Screw does the same during low RPMs. The T screw regulates how much fuel is sent to the carburettor while idling until the throttle is pressed.

Yes, it will fit. If you`re replacing the chain as well, just make sure you match… Q: I have a Poulan pro 20 inch…can I use an 18 inch bar and chain on it? Yes you can put a shorter bar on your chainsaw, just make sure it is the same brand style …

Once the engine has arrived at operating temperature, go back to the carburetor and adjust the air fuel mixture screw, or screws. Tightening the screw increases the amount of fuel, while loosening decreases the amount of fuel.

Run the engine for five minutes at half throttle to bring it to its operating temperature. Then, turn the idle mixture screw slowly clockwise until the engine begins to slow. Turn the screw in the opposite direction until the engine again begins to slow. Finally, turn the screw back to the midpoint.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

How to adjust carberater – Poulan P3416 16Inch 34cc 2Cycle Gas Powered Chain Saw

ANSWER : There should be a small screw hole beside the prime pump bulb where you can adjust the centrifugal clutch nudge ahead speed, and then adjust down again for the correct idle without any chain motion. However the gas tank filter inside really needs to be cleared of a paper thin film of dust which gets in there while refueling and won’t let gas through – this causes you to think the carb needs more gas or the idle setting is wrong.

Read Full Q/A … : P3416 16Inch 34cc 2Cycle Gas Powered Chain Saw

Poulan 4018 pp4018 – Poulan P4018 18Inch 40cc 2Cycle Gas Powered Easy Start Chain Saw With Case

ANSWER : Proper fuel mixture?

Read Full Q/A … : P3416 16Inch 34cc 2Cycle Gas Powered Chain Saw

What kind of oil do i MIX WITH THE FUEL – Poulan P3416 16Inch 34cc 2Cycle Gas Powered Chain Saw

ANSWER : 2 STROKE OIL.THE ONE 2 STROKE MOTORCYCLE USE.If you need more help post back!
Thumbs and testimonial are welcome!

Read Full Q/A … : P3416 16Inch 34cc 2Cycle Gas Powered Chain Saw

Where can I buy a wrench to adjust the carberator

ANSWER : Normally you would need a screwdriver.But the adjustment screws on your saw have plastic caps on them that will only turn about a1/8 of a turn.these are pre-set at the factory.you will need too take carb off and clean it out.if that doe,s not help it needs to be rebuilt or replaced.

Read Full Q/A … : P3416 16Inch 34cc 2Cycle Gas Powered Chain Saw

I would like to go down A bar size our two on my poulan wildthing

ANSWER : I have a Poulan Pro 295 20″. When I bought it I also bought a 16″bar and chain and have been using those since. They make the saw much easier to handle and are a better match to the available power.
The key dimension is from the bar’s mounting hole to its end. At the store look at the normal replacement bar for your 18″ saw, and pick out a 16″ or even 14″ bar with the same dimensions there. This can be easily seen by laying one bar over the other.

Read Full Q/A … : P3416 16Inch 34cc 2Cycle Gas Powered Chain Saw

Adjustment for coil. how many thousands of " – Poulan Wild Thing 2375 18" Gas Chain Saw 2.5 Cuin

ANSWER : Most coil to flywheel adjustment is fixed by the mounting screws
it will be around .002″ or have clearance as close to the flywheel without touching it as contact is a dead short

Read Full Q/A … : P3416 16Inch 34cc 2Cycle Gas Powered Chain Saw

I put oil in gas and gas in the oil can it be fixed

ANSWER : YES IT CAN. TAKE OFF BOTH CAPS AND TURN THE SAW OVER AND EMPTY THE TANKS. GO TO AN AUTO PARTS STORE AND BUY A GOOD DEGREASER THAT YOU CAN SPRAY IN THE TANKS AND WASH CLEAN. WAIT TILL DRY AND REFILL HTE RIGFHT WAY.

Read Full Q/A … : P3416 16Inch 34cc 2Cycle Gas Powered Chain Saw

Runs only on half chocked – Poulan P3416 16Inch 34cc 2Cycle Gas Powered Chain Saw

ANSWER : Remove the air intake and spray the carb down with carb cleaner. Buy new gas/mix. Put 1 oz of Sea Foam” into one gallon of the mix. Run two or more tanks of fuel and it should straighten out.

Read Full Q/A … : P3416 16Inch 34cc 2Cycle Gas Powered Chain Saw