Pro Chain Saw 46cc 20″

Experienced gardeners share their insights in answering this question :
Fill the oil reservoir to the top, each time you fill gas reservoir, a quart of oil usually should last you the use of a gallon of gas.

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

Q: How do I mix gas and oil? A: Mix 3.2 ounces of Poulan 2-cycle air cooled engine oil to one gallon of fresh unleaded gasoline to obtain the recommended 40:1 fuel to oil ratio.
Use unleaded gasoline and two-stroke oil mixed at a ratio of 2% (50:1). 50:1 gasoline to oil ratio.
Genuine Poulan 2 cycle engine oil; 40:1 ratio – 40 parts of gasoline to 1 part Poulan oil. This blend is designed to extend engine life and to provide smokeless exhaust.
This ratio indicates how much fresh, regular unleaded gasoline (containing no more than 10% ethanol) to mix with how much oil. For all Remington 2-cycle products, the ratio is 40:1. This means you`ll want to add 3.2 oz of oil to every gallon of gasoline.
If your manufacturer recommends a 50:1 fuel/oil mix, it means you need 50 parts of gas to one part two-stroke oil. To mix one gallon of fuel at 50:1, add 2.6 ounces of two-stroke oil to one gallon of gas, as shown in the chart below.
You can find Poulan Pro products both in-store and online at home improvement retailers, hardware stores, and mass merchants all over North America. We are here to help you tackle… ANY YARD.
The fuel and oil mixture should always be 2% (50:1).
It`s highly recommended a fuel to oil ratio of 50:1 for most 2-stroke engines. This means that for every 50 parts of fuel, there should 1 part of oil.
For example to mix 50:1 you use 50 parts fuel to 1 part oil, which equals one litre of fuel to 20 millilitres of oil.
A 100ml bottle is suitable for mixing with 5 litres of fuel to achieve a 50:1 fuel-oil ratio.
To get an idea of how much oil you need; the gap between the marks on the dipstick usually represents around 1 litre of oil, so you know that if your oil mark was at the minimum, you need around a litre to top it up. If it`s only halfway down, you probably need around half a litre.
For a mixing ratio of 1 : 50 you need 5 litres of petrol and 0.10 litres (100cm³) of STIHL two-stroke oil.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

<!– from fixya rte –>What is ball and chain oil – Poulan 16Inch 30 HP Electric Chain Saw 1630
ANSWER : Bar and chain oil…. it’s the oil used for the bar/chain assy on chainsaws… used anywhere else it might cause a major catastrophy

Read Full Q/A … : Pro Chain Saw 46cc 20″

Not much oil on poulan chain saw bar
ANSWER : There is some debris blocking from entering the bar and when sits it seeps out,clean bar and are under chain cover

Read Full Q/A … : Pro Chain Saw 46cc 20″

What kind of oil in the oil tank and how much for the remington electric pole saw ?
ANSWER : Bar & chain oil is the best. You can use regular or synthetic. Some say you can use atf (auto transmission fluid) or sae30 oil. I use bar & chain oil.

Read Full Q/A … : Pro Chain Saw 46cc 20″

Need a chain for 14in electric poulan chain saw the normal 14 in chain does not list the electric saw as one it will fit
ANSWER : Hello Jennifer;
The number of drive links, pitch and gauge of the chain need to be determined to answer your question. If you take your saw or just the chain to a local chain saw outlet a new chain can be fabricated in a very few minutes. This will save shipping and handling fees as well. While there get the numbers mentioned above. Once you have these you can likely find a low kickback chain in a local home center the next time the chain needs replacement.
The FAQs here can likely answer all your questions.
http://www.oregonchain.com/pro/service/faq.htm

If you have more questions or need additional help please reply below and I will get back to you. HTH & Good Luck.
Lou
Thank You for using FixYa.

Read Full Q/A … : Pro Chain Saw 46cc 20″

Poulan 14″ gas leaks bar oil all over, plenty on bar/chain, using thin synthetic oil.
ANSWER : Use actual bar oil sold for that purpose. It’s thicker and won’t run out like water. Synthetic oil is very thin does not have the proper density.

Read Full Q/A … : Pro Chain Saw 46cc 20″

What is the gas oil ratio – Poulan Wild Thing 2375 18" Gas Chain Saw 2.5 Cuin
ANSWER : Half and half

Read Full Q/A … : Pro Chain Saw 46cc 20″

Poulan 4018 pp4018 – Poulan P4018 18Inch 40cc 2Cycle Gas Powered Easy Start Chain Saw With Case
ANSWER : Proper fuel mixture?

Read Full Q/A … : Pro Chain Saw 46cc 20″

My 18 Inch chain saw will not keep oiling the Chain, I had it worked on and He said it was plugged. How do you unplug it with out taking it all apart. Is there a spot to blow air through. the Preacher..
ANSWER : Remove the chain bar and look just below the bolts holding it in place. You’ll see a small hole where the chain bar oil pump pushes out oil. Make sure this hole is clear then run the saw without the bar on.

Be CAREFUL of fingers!

You should see oil coming out of that hole. If not, you may need more serious work done with the saw (chain bar pump replacement).

Read Full Q/A … : Pro Chain Saw 46cc 20″