c etc.
Can you help?
Garden
Experienced gardeners share their insights in answering this question :
Is it the pull rope? if so you will need to remove the four to six bolts around the shroud. once shroud is off turn up side down, remove old rope. you will need to wind it up and if you feel tension then the spring is still good, if not then it is broken. if the spring is good wind it a few times, do not let go, and feed cord back through, tie a knot and burn the end, let go of rope and it will self wind, pull a few times to ensure the knot is going to hold. then reassemble, hope this helped Tim
How to Identify and Fix Common Gardening Problems ?
We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :
The stuck cables can be freed by a twisting motion, rather than by a straight pull. An effective twisting motion can be achieved by using a carpenter`s brace–without a bit–and channel locks. This procedure requires at least two people, preferably three.
In ideal situations, you`ll work with a conduit that still has old wire running through it. In these cases, you can simply attach the end of the old wire to the end of the new wire and use it as a pull wire, pulling the new line through the conduit.
Pulling wires can be difficult enough through straight runs of conduit, but throwing a few bends and turns in the run increases friction, making pulling much more difficult. That`s when you use a lubricant.
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
I have a yard machine 5.1 push mower. I can’t find my manual and it is low on oil. What type of oil does it take??
ANSWER : Most mowers take a 30 weight oil. that’s the 30 sae
Read Full Q/A … : Garden
Troy Bilt Lawn Mower pull Cord broken
ANSWER : There should be four bolts holding the cover on that houses the pull cord assembly take the bolts out look inside you should see the rest of the broken cord at the other end there is a spool that the cord rolls up in to pull the cord until it stops the other end of the cord is a not in the cord pull on the knot the broken peice should come out turn the spool 2 times in the direction that is against the pressre while holding the spool in place feed the new cord in through the whole that you pulled the broken cord out of then tie the cord in a knot wind the rest of the cord up then feed the other end of the cord through the new pull handle tie the cord in a knot put the housing back on
Read Full Q/A … : Garden
Pull cord is difficult to pull after third pull becomes stuck but will turn if pull hard repeats every three to four pulls.
ANSWER : No response to clarification request.
Read Full Q/A … : Garden
What is spark gap setting on a 21inch yard machine pus
ANSWER : Most all is .0030 thousands. Your owner’s manual will tell you.
Read Full Q/A … : Garden
I can’t start it because the pull cord is stuck and it happened after I installed a new blade.
ANSWER : If the recoil assembly has three screws holding it in place, remove them, lift the recoil assembly off and see if it works off the mower. If it does, reassemble.
Gary
Gary
Read Full Q/A … : Garden
When i pull the rope it backlashes half way through the pull
ANSWER : Hi, You have most likely sheared the flywheel key which puts the timing out. Remove the flywheel and replace the key. Regards Phil.
Read Full Q/A … : Garden
Craftsman service manuals
ANSWER : Prime 3 times start it if hard to start rebuild carb
Read Full Q/A … : Garden
Just installed a new pull cord…the cord does not retract. How do I fix the problem?
ANSWER : The best way i found is to twist counter clock wise a dozen turns,hold the spool with vise grips,feed the roop through all holes you need to go through, into the reel knot, i burn the knot, keeps it from slipping out,then slowly let the spring bring the slak in when i release the vise grips!
Read Full Q/A … : Garden
