Garden

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

Q: How do I mix gas and oil? A: Mix 3.2 ounces of Poulan 2-cycle air cooled engine oil to one gallon of fresh unleaded gasoline to obtain the recommended 40:1 fuel to oil ratio.
Without proper care, even the best Poulan chain saw can malfunction. During refueling, it is paramount to maintain the oil ratio for which its engine was designed. Poulan suggests a ratio of 40 parts fuel to 1 part oil.
Check the Carburetor

In warm weather, your Poulan chain saw may fail to start after sitting for 15 to 30 minutes because the carburetor has become vapor locked. This occurs when hot gas evaporates in the carburetor and prevents the right amount of fuel from reaching it.

There may be old or bad fuel in the carburetor float bowl. Over time, some of the ingredients in the fuel may evaporate, leaving behind a thicker, stickier substance. This sticky fuel can clog up the carburetor and make the engine hard to start. If the carburetor is clogged, try cleaning it with carburetor cleaner.
If a petrol engine chainsaw won`t start, it is usually due to an engine malfunction, specifically relating to the fuel system (which mixes the fuel with air and feeds this mixture into the engine`s combustion chamber) or ignition system (which produces the spark that starts combustion and thereby causes the engine to …
You want to mix 2.6 ounces of oil to one gallon of gasoline for a 50:1 mixture. If you`re mixing up two gallons of gasoline you will have to mix 5.2 ounces of oil to two gallons of gasoline for a 50:1 mixture.
Pre-mixed 2-cycle fuel comes with the chainsaw. To mix your own fuel you must obtain a 50:1 (or 2%) mixture ratio, pour 2.6 ounces of 2-cycle synthetic oil into one gallon of fresh unleaded gasoline.
The Poulan Pro 952030203 Bar and Chain Oil is Formulated for use by the logging industry, this oil helps prevent rust, resists high-temperatures, flows freely at low temperatures and has the ability to resist the extreme pressures bars and chains – bottle size is 1 Quart.
If you have an electric chainsaw that won`t start, first make sure that the power cable is connected to the mains, then check whether the cable and plug are damaged. If they aren`t, the problem could lie in the motor which, for example, may have worn or damaged brushes.
A dirty carburetor, bad gasoline and low-quality two-stroke oil that creates deposits all contribute to chainsaw starting problems.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

<!– from fixya rte –>How far to turn idle screw out after rebuild – Poulan 14 Woodshark Chainsaw
ANSWER : You’ll have to do a visual on this one. But you turn it out until the throttle plate just starts to move, where it can get a little air. This is the initial start position and you can fine tune afterwards.

Read Full Q/A … : Garden

I have a Pouan Pro. I can start it but then when I give it gas it seems to have no power. It doesn’t die, just gets no power. Occasionally it revs.
ANSWER : It may well be running too rich because the air filter is blocked, remove the filter and just try the revs again free running, if ok, clean/replace the filter.

Read Full Q/A … : Garden

Can you adjust the oil pump – Poulan Pro 42CC 2 Cycle Chainsaw, 18"
ANSWER : Depends on the saw. If it is adjustable then it will be adjusted from the bottom of the saw. Most have a diagram on the bottom showing which direction to turn the screw

Read Full Q/A … : Garden

My poulan pro 42cc is hard to start ,,, its1 year old an i’m not sure if its worn out from alot of use or if its with the ignition
ANSWER : Throw it out and buy a new one this is a throw away scoiety we live in due to cheap *** chinese **** oh yeah go green

Read Full Q/A … : Garden

Poulan 3816, back fires through carburator, wont start.
ANSWER : Water in the gas or carb needs to be removed and taken apart and cleaned

Read Full Q/A … : Garden

Maxtra CHAINSAWS CAN YOU SUPPLY CHAINOIL PLUGS?FOR maxtra 42CC
18″-ml 72tfgcsoo8 the plug i have will not stay in place .
ANSWER : I would check jackssmallengines.com the link is below. They supply Poulan replacement parts.http://www.jackssmallengines.com/poulan_chainsaw_parts_index.cfmGood luck.

Read Full Q/A … : Garden

Drive froze, will start but chain will not move even when loose.
ANSWER : 1. If the engine won’t develop high rpm’s, possiblely chain brake is applied. 2. If not that, likely clutch or sprocket.

Read Full Q/A … : Garden

Poulan pro 46cc will not idle
ANSWER : Fuel pump in carb is hard and not pumping. rebuild carb

Read Full Q/A … : Garden