Troy-Bilt
How to Identify and Fix Common Gardening Problems ?
We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :
Your leaf blower`s primer bulb can be at the heart of solving the problem of a leaf blower engine that is difficult to start. The primer bulb is designed to purge the carburetor of air, which can help your engine to start. However, if the primer bulb is cracked or damaged, it will not be able to perform this function.
Q: What is the outside diameter of the bulb? all primer bulbs are not the same size! quit telling everybody it will fit just because it fit yours…
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
Troybilt trimmer primer bulb collapses. it will start occasionally but will only run a few minutes.i have replaced the primer bulb and gas lines and still have the same problems.
ANSWER : It should have a small vent in the fule tank cap if its blocked the primer bulb will be sucked in as the fule pump can **** any fule from the tank
check the tank cap first,,,,,
check the tank cap first,,,,,
Read Full Q/A … : Troy-Bilt
How to replace a primer bulb for a tb70ss – Troy Bilt Tb70ss Gas Trimmer
ANSWER : Google the model number for a service manual or contact Troy for help.
Read Full Q/A … : Troy-Bilt
I need to tighten the drive belt between the engine and transmission on my Troy-Bilt 3312 GRS lawn tractor
ANSWER : I REPLACE THE DRIVE BELT AND THE MOWER STILL WON’T MOVE
Read Full Q/A … : Troy-Bilt
TROY BUILT RIDING MOWER MODEL13AX60KH011 – Troy Bilt 175HP Manual 42" Riding Mower
ANSWER : OK question
Read Full Q/A … : Troy-Bilt
Trying to replace the pull cord , can’t get last housing off to get to coile up old cord , the shaft has a nut on the end that the auger screws into but i cannot get that piece off as there is no where to put a wrench to stop the turning of the engine shaft so i can torque the nut in the other direction to get it off , what do i do to get this pull cord replaced?
ANSWER : Use an impact wrench it will hit the nut so fast it will loosen it befroe the engine car turn over
Read Full Q/A … : Troy-Bilt
Troy Bilt Lawn Mower pull Cord broken
ANSWER : There should be four bolts holding the cover on that houses the pull cord assembly take the bolts out look inside you should see the rest of the broken cord at the other end there is a spool that the cord rolls up in to pull the cord until it stops the other end of the cord is a not in the cord pull on the knot the broken peice should come out turn the spool 2 times in the direction that is against the pressre while holding the spool in place feed the new cord in through the whole that you pulled the broken cord out of then tie the cord in a knot wind the rest of the cord up then feed the other end of the cord through the new pull handle tie the cord in a knot put the housing back on
Read Full Q/A … : Troy-Bilt
Steering will not turn – Troy Bilt 175HP Manual 42" Riding Mower
ANSWER : Look for a broken t shaped part where the shaft and gear meet
Read Full Q/A … : Troy-Bilt
I have a troy bilt pony and the drive belt to engage to blades keeps coming off. I have replaced the belt and the pully what else could it be?
ANSWER : Well i would take a long look at the spring which holds the tension pulley in place. if it is weak, or not connected correctly, there will be inadequate tension and the belt can come off. I would also take a look at whatever fasteners keep the deck in place as if it is not kept to the rear, there again will be too much play in the deck belt.
Read Full Q/A … : Troy-Bilt
