The rubber cap on the spark plug can be pulled off the HT lead. Should this be the case? The chainsaw still works if I push the lead back into the rubber cap. If the lead has broken off the spring inside the rubber cap, how do I replace the whole HT lead including the spark plug cap?
How to Identify and Fix Common Gardening Problems ?
We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :
If your STIHL chainsaw is going to have a problem, it`s likely to be with a worn carburetor, bad spark plugs, loose fuel hoses, or clogged fuel lines. You should also inspect the fuel intake system and ensure that there are no compression issues.
For the best performance from your STIHL tool, we recommend that you always use the STIHL NGK spark plug.
A dirty carburetor, bad gasoline and low-quality two-stroke oil that creates deposits all contribute to chainsaw starting problems.
STIHL recommends replacing the spark plugs around every 100 hours of use. It`s a good idea to get in the habit of checking the condition of your spark plug after every 10 to 15 hours of use. If the engine is running well, the outside electrode should have light brown deposits.
How Long do STIHL Chainsaws Last? Information we found online suggests that Stihl Pro Chainsaws have a run time of about 2,000 hours. That means the saw would last you for a minimum of 5.5 years before dying. Keep in mind this time is rated for professional chainsaws and not for regular homeowner saws.
STIHL recommends that you do not run your engine at wide open throttle without a load. A blower is under a load at all times, a trimmer is under a load as long as the trimmer head is in place and the line is to the correct length, while a chainsaw is under a load when the bar and chain are in a cut.
With the choke in the “off” position, pull the engine`s crank cord through again. The engine should start in 1 to 3 pulls. Try it first without using the throttle control—unless recommended by the manufacturer.
A properly-tensioned chainsaw chain should still be just a little loose on the chainsaw guide bar, but the chain needs to be tight enough that you can`t pull the drive links out of the bar nose.
When engaged, the chain brake stops the chain from rotating around the saw`s guide bar. When using a chainsaw, you should always start it with the chain brake engaged so the chain does not move.
PULL, PUSH and KICKBACK are terms for the direction a reaction takes. PULL – When you are cutting on top of a log with the lower portion of the chain moving toward you, the chain saw will be pulled into the wood and away from you. PUSH – Cutting on the underside of a log pushes the chain saw toward you.
If you`ve used the correct procedure to start your Stihl trimmer and it does not start, the problem is likely related to either the spark, the fuel or the air circulation in the combustion chamber. More often than not, it`s an easy fix, possibly involving replacement of a spark plug or air filter.
If your chainsaw does not start, the fuel may be too hot. To prevent this from happening, always use fresh fuel and reduce your operating time when the weather is warm. If your chainsaw will not start, place it in a cool area away from sunlight for at least 20 minutes.
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
How to replace a oiler on a stihl chainsaw ? – Stihl Service Manual for 031AV Chainsaw with Parts List
Remove the worm, sealing ring and washer, loosen the pan head screws on the oil pump and replace. Check if the gasket is re-usable.
How to remove stihl 023 handle bar?
There are three mounting points. You need to remove the screws behind the plug caps with a T27 bit. Then, the tank should separate from the crankcase and you can pop the AV mount from the crankcase to replace it.
Starter coil on stihl 017 – Stihl 017 018 Ms170 Ms180 Chainsaw Starter Stbx759
If you are asking for the part number, it is 1130 400 1302 if you have two ground wires and one lead wire. If you only have one ground wire and one lead wire, the part number is 1130 400 1300.
I HAVE AN O17 STIHL CHAIN SAW AND IT LEAKS CHAIN OIL
EVEN WHEN IT IS NOT BEING USED
That can happen. When you go to store it, open the oil cap and then close it to lose the pressure the pump builds up inside.
Is there supposed to be a cyntrifical clutch on a stihl 028 av super electronic quickstop?
Yes; see page 37 in your OM. You read it before using your saw right?
If you have more questions or need additional help please reply below and I will get back to you. Thank you for using FixYa and Good Luck. HTH
Saw will start but dies when rev – Stihl 16" Chainsaw Bar Chain Saw 018 025 Ms 180 250
Check the pick up fuel line in the gas tank. If there is a fuel filter at the end of the line,remove and clean or replace. Use a small fexible wire to hook line and pull out thru gas tank opening.
I need screws to replace the muffler – Stihl Model 038, Repl. 1119 790 170
If you replace screws make sure they have vibra-tite or other thread lock to keep from vibrating loose.
Here: Vibra TITE 213 VC 3 Threadmate Threadlocker 65 to 165 Degree 5mL Tube Red
Online chainsaw parts:
Stihl Chainsaw Parts Chainsaw Parts Discount Online Parts
Find a manual for a stihl 015l chainsaw – Stihl Service Manual for 015, 015L Chainsaw Model 1116