Garden
Experienced gardeners share their insights in answering this question :
No response to clarification.
How to Identify and Fix Common Gardening Problems ?
We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :
Generally speaking, you will perform one of the following release actions: pull the foot lever above the foot pedal to release the e-brake, press the button on the hand-activated brake and press the center lever down, push the e-brake button on the car`s console, or shift the stick lever beneath the dashboard.
When engaged, the chain brake stops the chain from rotating around the saw`s guide bar. When using a chainsaw, you should always start it with the chain brake engaged so the chain does not move.
Generally speaking, you will perform one of the following release actions: pull the foot lever above the foot pedal to release the e-brake, press the button on the hand-activated brake and press the center lever down, push the e-brake button on the car`s console, or shift the stick lever beneath the dashboard.
If the springs are broken, the clutch pads won`t retract, preventing the chain from stopping. If the clutch pads are sticking, the clutch drum will stay engaged and continue to turn. If the springs are broken or the clutch pads are sticking, replace the clutch assembly.
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
My chainsaw starts when there is no bar and chain on it but when I put the bar chain and side casing back on tighten the chain and pull the starter cord it is hard to pull and then the chain goes loose again
ANSWER : Have you just replaced the chain?If so there is a possibility the chain and drive sprocket don’t match causing the engaging spurs to ride on the sprocket teeth
Read Full Q/A … : Garden
Pull cord is difficult to pull after third pull becomes stuck but will turn if pull hard repeats every three to four pulls.
ANSWER : No response to clarification request.
Read Full Q/A … : Garden
What causes the chain on my 240E to jump off the chain bar often, the chain tenson is correct.
ANSWER : Is the bar bent?try and flip it over and see if it falls off the other side if you can see a bend
Read Full Q/A … : Garden
Chain keeps falling off – Poulan 18" Chain Saw Replbar (small Saws)
ANSWER : Your chain is too loose. If you’re using an old chain, you might need to have a link taken out of it. You can find replacement chains for your saw at Hyperparts.com. Use the application lookup link at the top of the page with your model # to make sure you order the right chain.
Read Full Q/A … : Garden
I was using the saw as a chain saw last weekend to cut up an old tree stump when the chain came off. I don’t know how to access it to put it back on and don’t have a user manual. The saw belonged to my late father and I don’t know if he even kept the manual.
ANSWER : You will have to remove the cover on the side the chain bar goes into. There should be one or two nuts holding the cover on the side. The is also a chain tension adjuster you may have to loosen to put it back on. Make note of the direction of the teeth on the chain. It is an directional chain. The tension adjuster is usually a flat head screw on the front side right beside the chain bar.Unless it is a really old saw, manuals are available from most manufacturers for free download. See if you can locate a brand name and model number.
Read Full Q/A … : Garden
Chain saw won’t start – pull starter pulley hard to pull?
ANSWER : If it worked fine the last time you used it, then pull the spark plug and try pulling the rope. See if it’s easier or if gas shoots out of the plug hole. I’ve seen this happen when the diaphram in the carb goes bad from sitting over winter. It loads up the cylider with fuel and makes it very difficult to pull the rope. If there is no fuel in the cyliner and it’s still hard to pull, make sure there is nothing binding the clutch/sprocket. I’ve had chucks of wook lodged in there that caused it to bind the crank output, which resulted in a hard pull on the rope as well.
Read Full Q/A … : Garden
Chain saw chain is loose
ANSWER : Loosen the side cover nuts, then turn the adjuster CW to bring the chain up to the lower edge of the bar, then check to see if the chain will move fairly easily by hand. Tighten the clamp nuts and recheck tension. If chain seems to get loose quickly again, it may not be sharpened correctly causing heat to build in the chain. You should see no reflection of light from the cutting edges if filed correctly and the saw should require very little pressure for it to cut rapidly. Hope this helps!
Read Full Q/A … : Garden
My ics 633gc concrete saw seems to have to much compresion to pull start
ANSWER : Any chance it was run with little to no lubricant? When they get hard to pull that is usually the first sign of the engine getting ready to seize
Read Full Q/A … : Garden
