Yard Machines

Experienced gardeners share their insights in answering this question :
This is a messy and dangerous job. Gasoline vapor can ignite and you need to be able to handle any fuel that is present. Then you need to remove the carb and tank assembly from the intake on the engine. You can then remove the tank from the carb. If you are using gasoline that has acohol in it, it may have ruined some of the seals and plastic parts like a float. You should order the repair kit from the maker. Then you can take all the parts off the carb and use a carb cleaner from any autoparts store that is either a spray or a soak. The spray means that you should use eye protection. When the unit has been cleaned then you need to put everything back on it. There are fuel adjustment screws that have to be reset after you take them out for cleaning.

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

Use Carburetor Cleaner

Fortunately, you can generally do this without even taking the carburetor out of the engine. Start by purchasing some commercial lawnmower carburetor cleanerOpens a new window, which comes in a simple spray can and will make it easy to clean the inside and outside of the carb.

Use carburetor cleaner to remove deposits, clogs & debris

Luckily, you can take care of many of these problems quickly and easily; often without even removing the carburetor from the engine.

The best way to achieve a clean carburetor is to soak it in a chemical solution to dissolve material buildup and remove gunk. Berryman Chem-Dip Carburetor Parts Cleaner and Pine-Sol are both effective products for this process.
Put the carburetor float and other components in a large container with your Simple Green Pro HD solution, and soak thoroughly. Use a brass brush to scrub all metal components, and a stiff nylon brush to scrub plastic pieces. Make sure the tiny vents get cleaned.
Get your can and spray the liquid on the carburettor. Make sure you don`t go overboard with spraying the liquid as it may end up harming the device. Rest assured that WD-40 is potent enough to work its magic even if it is sprayed decently on the carburettor.
After removing gasoline from the tank and carburetor, add a mixture of Sea Foam followed by 8 ounces of fresh gasoline (1 to 2 ratio). 5. With the cleaning mixture in the fuel tank, crank/prime/rope-pull the engine to draw the cleaning mix into the carburetor(s). 6.
Rinse all carburetor components in a bucket of clean water, and allow to air dry completely. For small holes and vents, use a can of compressed air to remove any excess moisture. Reassemble and replace.
In most cases, once a year is sufficient, especially if the road you`re driving on isn`t dusty and your gas tank isn`t rusted, so there`s no rust or dust that will stick under your carburetor bowl.
The carburettor cleaning fluid is a concentrate and is added to water at a ratio of 10: (1 parts cleaning fluid to 10 part water). For heavily soiled components, this can be strengthened to 7:1. The working temperature of the ultrasonic cleaner should be set between 50 – 80 degrees centigrade.
But the good news is carbs are relatively easy to clean so the task should be near the top of your `jobs to do` list if your bike is playing up. Problems generally arise because carbs rely on fuel going through very small holes, which can be easily blocked by gunk.
If you opted to buy a chemical dip, you can place your carburetor parts in it to soak. Alternatively, you can spray carb cleaner throughout the various channels in your carb (such as the spots where the jets, float pin, and air and idle screws were). Also spray cleaner through any dirty jets.
But the good news is carbs are relatively easy to clean so the task should be near the top of your `jobs to do` list if your bike is playing up. Problems generally arise because carbs rely on fuel going through very small holes, which can be easily blocked by gunk.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

Yard machine 16.5 will turn over but not start
ANSWER : Squirt some staring fluid into it star if not check for spark if sparking need to rebuild dirt in it or water in gas if not sparking check fuse or switch behid dash

Read Full Q/A … : Yard Machines

I have a yard machine 5.1 push mower. I can’t find my manual and it is low on oil. What type of oil does it take??
ANSWER : Most mowers take a 30 weight oil. that’s the 30 sae

Read Full Q/A … : Yard Machines

My engine runs about 5 mins. and then just cuts off????
ANSWER : Dirty vent hole on carb rebuild it

Read Full Q/A … : Yard Machines

How may yards in a mile – Mtd Products Yard Machines 158CC Tiller
ANSWER : 1,760 yards = 1 mile

Read Full Q/A … : Yard Machines

Where do i change the oil on 5.5 hp. 21 inch cut mtd push mower
ANSWER : Most of these machine will have an oil drain plug under the mower deck near the center of the blade. 80 to 90 % of them are a 3/8″ drive female plug that can be removed with a ratchet and a short extention.When you put it back in it is a good idea to clean it well and wrap the threads with 2 or 3 layers of teflon tape

Read Full Q/A … : Yard Machines

I charged the battery on my yard machines 12.5 riding mower but when I tried to start it I get nothing. The lights don’t even come on in the accesory position
ANSWER : Sounds like a dead battery.if it’s more then 1-2 years old time to get a new one.also check the fuse in the line close to the start relay.

Read Full Q/A … : Yard Machines

How do I replace the pull cord on my 31cc yard machine tiller?
ANSWER : Carefully . the recoil spring will want to fly apart .

Read Full Q/A … : Yard Machines

Need operators manual for MTD tiller 214-430-000
ANSWER : Go to MTD website to obtain manual or google manual by model number followed by the word mtd or tiller

Read Full Q/A … : Yard Machines