Garden

Experienced gardeners share their insights in answering this question :
On what? Where? There are dozens on a riding mower/tractor.

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

5 Steps to Replacing your Greenhouse Glazing:
  1. Remove the clips that hold the glass in place.
  2. Now remove the broken glass. …
  3. Clean the seal strip found around the aluminum frame – check it is undamaged. …
  4. Install the new polycarbonate pane.
  5. Replace the clips – there should be a clip every 12 inches.
19 févr. 2018
Just staple every 4 inches through the tape and the plastic film into the wood. The tape will hold the plastic film in place without tearing. The tape is very flexible and easy to use — unroll, hold in place, and staple. It is white and contributes to a neat and attractive structure.
Just staple every 4 inches through the tape and the plastic film into the wood. The tape will hold the plastic film in place without tearing. The tape is very flexible and easy to use — unroll, hold in place, and staple. It is white and contributes to a neat and attractive structure.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

How do i rewind the recoil spring on my craftsman lawn mower?
ANSWER : Normally these small engines use a clock spring to retract the rope.
Remove the cover on the top and you should find the spring either broken or the tab where the spring end has broken off or jumped out of the mount.
You will need to pre-load the spring with enough tension to retract the rope.
Remove the pull handle from the rope, load the spring and then wrap the rope around the pully holding the pully and spring in the loaded position. place the end of the rope through the hole and tie up the handle. The rope should pull and retract without being installed on the engine.
Best explained here…
https://www.youtube.com/watch?v=tmo6oYOJJ4U

Read Full Q/A … : Garden

Spring is broken
ANSWER : Craftsman rider mower brakes failed all of a sudden a spring broke but I can not find where the spring attachs on the blueprint

Read Full Q/A … : Garden

How to get owner's manual – Troy-Bilt Pony Garden Tiller
ANSWER : Most of the time u can go to the place of sale and get one or just call
the company and get or go one line with tyap code and modal number a
and see if that helps.

Read Full Q/A … : Garden

Cannot get the recoil spring on model 18r back in housing!
ANSWER : If it goes into a metal housing that is like a can lid with short sides and has one area that is open onthe side and the whole thing has a small hole in the center of the flat side….Take the metal housing, lay it flat on a table or other flat surface. Figure which way the spring would go. Lay the small end of the spring in the housing with the spring wire going out the open slot. Now all you do is wind the spring in by turning the housing. You must keep the spring in the housing with your other hand, maybe a flat piece of wood or something to hold the spring from jumping out. Once you have it all in the housing, reinstall it. If the spring is backward, CAREFULLY pull the spring out until it is no longer under tension, flop the spring over and go again…Good luck…Lee

Read Full Q/A … : Garden

BROKEN SPRING A spring broke on my lawn tractor. It is a yardman model 13AG601H729 When this happened I lost the accelerator pedal. I since found that the belt has slipped off the pulley, which I have fixed. I do have drive pedal for forward and reverse, but I still do not know where this spring goes. I went to the dealer and ordered a new spring. When the spring broke it was still attached to a pin, but I do not know where the other end of this spring goes? This pin is bolted to the frame and has the range to attach to pulleys under the mower, but where???? Can you help?
ANSWER : Hi, check under your seat. at the frame there should be a bracket that the rod and spring goes thru and right to the pedal.

Read Full Q/A … : Garden

I have a 20″ bar chain saw (51 Air Injection)
ANSWER : The part no. of the spring is 501763101 it comes in a plastic keeper so is very easy to fit, check the web for sellers.

Read Full Q/A … : Garden

Rewind pully spring – Poulan Pro Chain Saw 46cc 20"
ANSWER : Recoil Spring Rewind
I invert and secure the housing and rewind the spring large coil to small (need eye protection, both hands and no women around work area!). I’m right handed so I tension the spring enough to insert it inside the previous coil while holding what has already been installed with my left about 180° from my right hand. The tension will hold the spring in the housing once completely inserted. Then bend slightly the inner most part to engage the starter spool. It will require about 2 turns of pretension for it to retract properly.If you’re lucky you can pull the cord out enough for a pretension then slightly raise and add the withdrawn cord to the spool. HTHLou

Read Full Q/A … : Garden

Won't seal and hold pressure – Ace Hardware Acer Spray and Go Sprayer
ANSWER : Try smearing some Vaseline on the gasket that goes around the pump shaft at the top.

Read Full Q/A … : Garden