Hozelock

Worked ok from out of box now stopped working no motor start up power ok

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

A: We recommend soaking the trigger in a 50/50 mix of warm water and vinegar, as the problem may be related to either a rubber seal, a build-up of mineral deposits or sediment around the mechanism. Ideally the gun should be soaked for 30-40 minutes.
Why does the Auto Reel not retract all the time? We recommend pulling out all the hose. Clean any excess debris from the outside of the hose such as sand and dirt with a damp cloth. Now, let the hose retract slowly by walking back to the reel holding the end stop.
The reason for this is because a build up of water pressure. On the water inlet or coupling the water can cause a pressure build up, popping the garden hose off. The aqua stop is a valve in the end of the garden hose connection that restricts water flow.
Most low-pressure problems come from the hose itself. Check for leaks, twisting, and blockages. Fixing these issues will increase the pressure. If your hose is in good shape, then try a high-pressure nozzle or pressure booster to increase your hose`s power.
This is called being “calcified” in place and is usually caused from having an aluminum hose and brass spigot. Over time, white calcium will form and almost glue the hose to the spigot.
One of the most common reasons a garden hose spray nozzle leaks is because the O-ring that seals the nozzle to the hose is damaged or missing. If you can see that the O-ring is damaged, simply replace it with a new one. If the O-ring is missing, you may be able to find one at your local hardware store.
You can fix a leaky connector with a new rubber hose washer. With the water off, disconnect the leaky hose end. Use needle-nose pliers or a small screwdriver to help pull out the worn gasket inside the coupling.
Firstly ensure that you are releasing water pressure from the hose before retracting. The added water pressure may be the cause of this issue. If this does not help, pull your hose out to its full length then let it retract back in. This should re-align the hose on the drum.
Low pressure at your garden hose spigot can be caused by one or a combination of issues, such as clogged or leaking pipes, excessive corrosion in the spigot valve or a lack of water pressure coming from the street.
Does not rotate/does not rotate reliably Ensure the sprinkler is pushed all the way into the ground, so that the hose connector is only just above the ground. If the sprinkler is too high, it will vibrate and these vibrations can prevent the sprinkler from rotating. This sprinkler also requires good water pressure.
A good garden hose should last 5 to 10 years.
Does not rotate/does not rotate reliably Ensure the sprinkler is pushed all the way into the ground, so that the hose connector is only just above the ground. If the sprinkler is too high, it will vibrate and these vibrations can prevent the sprinkler from rotating. This sprinkler also requires good water pressure.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

Does not run, will start with starting fluid – Mantis 2-Cycle Tiller
ANSWER : You should never use starting fluid on this model.

Add a couple of ounces of 100% acetone (available at Walmart) to some fresh fuel. Attempt to start for several pulls. Let sit for several minutes and repeat until it sounds like it wants to run.

Then watch this video and do it:

http://www.alamia.us/mantis_parts_s/148.htm

Read Full Q/A … : Hozelock

Toro clear won't start – Toro Power Clear 621 R
ANSWER : Bad gas , plug ,air filter , no spark ck all need all 3 to start

Read Full Q/A … : Hozelock

Strimmer wont start plug very dry when i remove it?
ANSWER : Sounds like the gas is not getting to the cylinder—remove carb and disassemble–make sure all jets are clear and the float valve moves freely.

Read Full Q/A … : Hozelock

Why do I have hard time starting my ariens snowblower when cold?
ANSWER : Does it have a primer bulb been seeing a lot of the bulbs with cracks

Read Full Q/A … : Hozelock

Mower won’t start. Toro mower..engine won’t turn over. Cleaned sparkplug…checked air filter..weather cool. Followed instructions for cold engine…prime witrh three pushes of the bulb..wnon’t even hint at a start..
ANSWER : Something everyone over looks is oil. Did you check the oil? You seemed to mention everything else but. If you have a low oil switch with low oil it will not start

Read Full Q/A … : Hozelock

Tines continue to work with out touching safety or throttle. they engage as soon as I start the engine.
ANSWER : Remove H (high) L (low) plastic caps to allow you to further adjust the flow and you will be going. H (red) further out about 11 threads exposed and L (low) about 8 exposed; adjusting the low side will stop the tines, but remove tines before making any adjustments, thanks

Read Full Q/A … : Hozelock

<!– from fixya rte –>Rj19lm plug gap for a 195cc 4cyl lawnboy – Lawn-Boy lawnboy" Mower Blade 21"
ANSWER : As a starting point in my shop i always use 0.30 in. For all my mowers

Read Full Q/A … : Hozelock

Snow blower wont start
ANSWER : Clean the fuel out and the carb , make sure you are getting spark close the choke to start then shut if off or it will foul the plug

Read Full Q/A … : Hozelock