Garden
How to Identify and Fix Common Gardening Problems ?
We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :
Sometimes, when your starter rope will not retract into your leaf blower, it can be because it is jammed between the pulley and the housing, or it is wrapped around the hub. In this case, you will often be able to fix the symptom by simply opening the machine and untangling or removing the rope from where it is stuck.
The most common reason for the cord refusing to rewind is a broken or worn out recoil spring. This tiny spring hooks onto the pulley and is stretched out when you pull the cord; when you let go the spring is meant to snap back to its original position.
The problem may be in the recoil starter itself. A tangled coil of rope or a broken spring may be the problem. In many cases the recoil starter is easily replaced as a single assembly. DO NOT attempt do take the starter apart.
Firing too soon – When the timing is off, it means the plug is firing outside its narrow window of operation. It`s firing too soon and that causes the piston to reverse, causing the crank to turn counterclockwise and snap the pull cord from your hand as it does so, Ouch!
The problem may be in the recoil starter itself. A tangled coil of rope or a broken spring may be the problem. In many cases the recoil starter is easily replaced as a single assembly. DO NOT attempt do take the starter apart.
To make pulling the cord easier, shift the lawnmower height up to start the machine, then lower it back down to your desired grass height to begin cutting.
When your trimmer starts and runs on choke, it could be because the check valve in the gas cap is clogged. Start the trimmer and gently unscrew the gas cap halfway off. Turn the choke off and assess. If the engine is still running, that means the gas cap may be the culprit.
The recoil starter is the pull-start mechanism on the back of the engine that enables you to start your snow blower or lawnmower. The starter cord is also called a starter rope.
Every petrol lawn mower owner will experience this issue at some point: The starter cord won`t pull or is very hard to pull. This problem is usually caused by the engagement of the engine flywheel brake. Check to see if the flywheel brake is pressing against the handle before pulling the rope again.
Some common issues that can lead to a cord being harder to pull are hydro locking, which usually occurs because of oil spilling into the exhaust area, and a misshapen crankshaft. The misshapen shaft can generally be detected due to the noise it makes. The off-ness of the shape causes the cord to be hard to pull.
Why Is Your Lawn Mower Pull Cord Hard To Pull? Your lawn mower pull cord hard to pull is because of the way you pull the cord, the area where your mower is located when you are trying to start it, because it has a blade obstruction, or because of a starter mechanism-related issue.
Why Is Your Lawn Mower Pull Cord Hard To Pull? Your lawn mower pull cord hard to pull is because of the way you pull the cord, the area where your mower is located when you are trying to start it, because it has a blade obstruction, or because of a starter mechanism-related issue.
Why Is Your Lawn Mower Pull Cord Hard To Pull? Your lawn mower pull cord hard to pull is because of the way you pull the cord, the area where your mower is located when you are trying to start it, because it has a blade obstruction, or because of a starter mechanism-related issue.
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
Does this blower use 2 cycle mix; I have a homelite vac attack II 200mph blower and it is having trouble starting
ANSWER : Yes it will use a fuel mixture of 40:1(3.2 oz of two cycle oil to 1 gallon of gas). Any fuel sitting over 30 days now is considered bad fuel. All the manufacturers schools this year and told us this. We are finding it to be true.Good day.
Read Full Q/A … : Garden
What is the fuel mixture for the Homelite vac attack II
I pulled the weed eater to start it and the pull cord stayed out and won’t return back it was working fine early about ten minutes before this happened need help with fixing can work on this myself if i can find out what’s going on “need help in St.Catharines”.
ANSWER : You need a new rewind spring most likely it comes as a part with the reel.
Read Full Q/A … : Garden
Pull cord is difficult to pull after third pull becomes stuck but will turn if pull hard repeats every three to four pulls.
ANSWER : No response to clarification request.
Read Full Q/A … : Garden
Troy Bilt Lawn Mower pull Cord broken
ANSWER : There should be four bolts holding the cover on that houses the pull cord assembly take the bolts out look inside you should see the rest of the broken cord at the other end there is a spool that the cord rolls up in to pull the cord until it stops the other end of the cord is a not in the cord pull on the knot the broken peice should come out turn the spool 2 times in the direction that is against the pressre while holding the spool in place feed the new cord in through the whole that you pulled the broken cord out of then tie the cord in a knot wind the rest of the cord up then feed the other end of the cord through the new pull handle tie the cord in a knot put the housing back on
Read Full Q/A … : Garden
What is the gas ratio for Homelite Vac Attack II
ANSWER : The mix that I would use is one ounce of two cycle oil per quart or four ounces of two cycle oil per gallon of unleaded gasoline. Hope this helped and best wishes.
Read Full Q/A … : Garden
Pull starter cord wont return, so cannot pull start
ANSWER : You need to order the replacement coil spring, this is a tricky job to replace and if you are not handy, your best bet is to take it to a small engine repair depot.
Read Full Q/A … : Garden
My homelite super 2 chainsaw keeps flooding. it was running fine and all of a sudden its flooding. any help is welcome
ANSWER : Needle valve in carb. maybe hung open. Or diaphragm may be bad. You will need to remove carb. and clean and replace all worn parts. Go to homelite.com to find manual for the saw.
Read Full Q/A … : Garden
