Garden
How to Identify and Fix Common Gardening Problems ?
We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :
The most common reasons why your automatic oiler isn`t working are: Your chainsaw`s oil tank is empty. The chainsaw oiler is clogged. The oil pump is broken.
Without lubricant, the speed at which the chain moves over the chainsaw bar can cause some serious friction. A slowed-down chain and excessive fuel burning mean there`s a lot of friction between your bar and chain, which means a lot of heat is being produced that could do major damage to your saw.
With a single contact with the ground while running, a chainsaw can become very dull. This is because the ground contains sand and dust which is abrasive and contains a lot of tiny rocks. To avoid such occurrences, avoid cutting wood placed on the ground.
Without lubricant, the speed at which the chain moves over the chainsaw bar can cause some serious friction. A slowed-down chain and excessive fuel burning mean there`s a lot of friction between your bar and chain, which means a lot of heat is being produced that could do major damage to your saw.
With a single contact with the ground while running, a chainsaw can become very dull. This is because the ground contains sand and dust which is abrasive and contains a lot of tiny rocks. To avoid such occurrences, avoid cutting wood placed on the ground.
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
I just started up my new 16″ Homelite and the engine starts, but the mechanism that powers the chainsaw isn’t rotating… any suggestions?
ANSWER : The engine needs to be accelerated to make the chain turn. The chain should not be so tight on the bar that you can’t turn it by hand. Make sure the chain brake is off by pulling back on the brake paddle which has a ‘toggle’ effect–it should snap over to the new position. If still having problems, it is time to return for warranty exchange or repair. Hope this helps!
Read Full Q/A … : Garden
Maintenance gears trouble shooting gears _ chain _coubling_bearing
ANSWER : Unable to help. What is problem on what product?
Read Full Q/A … : Garden
Homelite 330 chain saw no lubrification to the chain
ANSWER : Allot of times this is caused by dirt plugging up the outlet. Pull the side cover that holds the bar on and clean using carb cleaner and compressed air. You should see a small metal tube or hole where the chain runs at the top, make sure it is clear. If you remove the cain and the bar you can start and rev the saw to make sure oil is weeping, it won’t squirt out.
Read Full Q/A … : Garden
HOW DO YOU ADJUST TENSION ON CHAIN FOR HOMELITE UT10519
ANSWER : Hi,Turn the tightener till the chain in the center of the bar at the bottom just hangs down about a 1/8″….this will be good… too tight and the chain will not turn…too loose and it will come off…that 1/8″ is usually great for any saw…heatman101
Read Full Q/A … : Garden
Trouble shooting shurflo water pump problem
ANSWER : Try bleeding all the air out of the system or the new pump might be faulty.
Read Full Q/A … : Garden
BAR OILER NOT WORKING GEARS OK .WILL THE TANK PLUG UP . HUSKY 340
ANSWER : Hello slehman629,Take off the chain and bar and you can clean out the oilier tube with a piece of wire or a dull drill bit a small screw might work.It is just saw dust that gets packed in there. Thank you for using fix ya.
Read Full Q/A … : Garden
Homelite ut No. 10748 textron New sitting long
ANSWER : Is there bar oil in the tank? Oil pump and/or pickup tube in oil tank are usual suspects.
Read Full Q/A … : Garden
Cylinder compression Can't start due to compression built-up. Can't spind the engine over fast enought. Take spark plug out and engine spind freely.
ANSWER : Look on the side of the cylinder for the compression release valve
Read Full Q/A … : Garden
