“Chain Saw – 16” Bar, 3 Hp

Experienced gardeners share their insights in answering this question :
Verify you have oil in the oil fill tank. Try cleaning inside the drive sprocket cover. Release the chain tension and carefully dislodge the bar and chain assembly. Clean sawdust and debris from behind and inside the housing and behind the bar. Use a wisker wire to clean the through ports and channels on bar( these ports are the path that the oil travels to the drag groove that the drive links on the chain uses to pull the oil to the tip of the bar).
Please refer to this link below for your saw maintenance-
http://www.chainsawsdirect.com/manuals/HUSQ_445_MAN2.pdf

If this does not correct the problem contact Husqvarna customer service or a local service repair.

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

Model: 445 (Made in Sweden)
Husqvarna 445 (16″) 45.7cc Gas Chainsaw.
Easy to start and has plenty of power. I use the Husqvarna premix fuel that can be purchased at Lowe`s. The chainsaw is not to heavy at 10.5 lbs.
You`ll typically find somewhere between 66 and 72 drive links on a chainsaw chain. 16-inch bars typically have 66 drive links, while 18-inch bars usually have 72. Wear thick safety gloves during this step to minimize your risk of injury.
Husqvarna AB is a Swedish industrial company, one of the world`s largest manufacturers of saws, lawn mowers and garden equipment, as well as tools for stone cutting and for the construction industry.
The Husqvarna Group (Swedish pronunciation: [ˈhʉ̂ːsˌkvɑːɳa ˈɡruːp]) is a Swedish manufacturer of outdoor power products including robotic lawn mowers, chainsaws, trimmers, brushcutters, cultivators, and garden tractors.
Husqvarna 455 Chainsaw 20″ 3/8″ Bar and Chain – OEM.
The Husqvarna 455 Rancher has a chain pitch of . 325 inches or 3/8 inch. It also has a recommended bar length of a minimum of 13 inches and a maximum of 20 inches.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

I broke the throttle trigger on a 445 Husqvarna chainsaw. I removed all of the screws etc from the orange handle bar. I am still unable to separate the two orange pieces. I do not want to force and break other pieces. Is there a trick to separating them?
ANSWER : The two halfs of the rear handle do not seperate, once you have removed the r/h side grip you can remove the throttle lock, you then need to remove the pivot pin from the trigger with a pin punch, the trigger can then be pulled down and out, you may need to disconnect the throttle wire from the carb if you cannot drop the trigger far enough to remove the wire from it.

Chain brake for 445-need the handle part – Husqvarna , No.455 Rancher, 20" Gas – Powered Chainsaw
ANSWER : The hand guard is part no. 544082601, check the web for prices and availability.

Husqvarna 240 want start at all – Husqvarna Chain Saw 18" 450 Model 966955438
ANSWER : Sounds like the ignition module or spark plug. The ignition module is what controls the spark plug that gives your saw the firing capabilities. Before you purchase one of those, replace the spark plug and see if that works. The 240 is a newer husqvarna; so I am skeptical to say it is the ignition module. However, any new product can have a bad part on it. Your saw may have gotten flooded and won’t start. Make sure your gas mixture is 50/50 gas to mixing oil. Always use fresh gas. If you make up gas and don’t use a whole gallon at a time, put some fuel stabilizer in the mixture; so it will still be fresh the next time you use it.

What information can you tell me about a Husqvarna chainsaw model 61 with serial number 6136460. Does it indicate the year?
ANSWER : Most of the CDI modules have been superseded to part no# 544018401check with your local dealer to verify.

We have a husqvarna cth 170 and we cant seem to reverse it… have any ideas on how?
ANSWER : I have a Husqvarna YTH2348 that clicks when i try to start… I had the battery tested and changed the solenoid and still won’t start. How do I check the starter????

Loosen or tighten chain on a 445 Husqurna Rancher chain saw
ANSWER : If this is the tooless system, flip open the wing on the bar cover securing nut, slacken off one turn, now use the knurled wheel in the cove to slacken, or tighten the chain, if it has two 13mm bar nuts, slacken them off one turn each, then use a flat blade screw driver through the side cover, betwwen the bar nuts to adjust the chain, the screw is quite small so clean away the saw dust to locate it.

Kill switch doesn't work, how do i fix it? – Husqvarna 350 18 Inch Gas Chainsaw 52CC Fully Assembled Brand New 18"
ANSWER : The switch connects directly to the coil body of the ignition module. You may have to remove the left side cover to expose the ignition module. The switch, when off, connects this wire to engine ground. There may be debris in the contacts of the switch that prevent contact. You will have to remove the air cleaner assembly and maybe the carburetor itself to access the switch. Good luck!

How to start a Husqvarna 445? – Husqvarna 16" Chainsaw Chain Saw Bar 508912166
ANSWER : Set choke to full on. To do this depress throttle all the way down and set choke lever to on. Pull starter rapidly until saw fires . Once it has fired set to start and pull starter cord until it starts. If it doesn’t start in ten – twelve pulls,reset choke for two or three pulls,then switch back to start. Pull starter cord until it starts. When it starts it wii be at full R.P.Ms. Let run for twenty to thirty seconds. then move switch to run. Hope his helps, Thanks