re was a lot of oil pouring out.
What kind of oil should I use, and how much?
And is there any possibility to get a link to a manual? (Owner and Repair/service)
Thanks
Garden

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

If the pump is leaking, the cause may be minor and easy to repair. Check the seals, packings, and O-rings for wear. These can easily be replaced, saving you the cost of a new pump. However, major leaks such as the ones caused by cracked or damaged plungers, can lead to pump failures.
Begin isolating the problem by hooking a water hose to the washer`s inlet and turning it on. If water flows out the outlet, you know water is cycling through. If not, chances are your inlet filter is clogged. Remove and clean it, and you should be good to go.
A pump leaking water indicates that there is something wrong such as bad water seals/packings or a broken ceramic plunger, or something minor like a leak o-ring. Any of these problems can be minor at first, but prolonged neglect can lead to bigger problems.
Pressure washer water pumps need relatively low oil recommended by the manufacturer, as specified in the owner`s manual. (Purchase pre-measured bottles of pump oil for water pumps without dipsticks.) Never use special oil additives or detergents, unless specified in the owner`s manual.
The number one cause of low or no pressure when using a pressure washer is a blocked or worn nozzle. Blocked nozzles will prevent water from escaping, while a worn nozzle will allow too much water to pass through, causing the pressure to drop.
If your pressure washer is refusing to work or even turn on, the culprit could potentially be the power switches. Most pressure washers use two micro switches that disconnect both the live and neutral connections between the supply and the motor. These switches can jam cutting the power out from reaching the motor.
You can measure the head pressure by installing a pressure gauge or manometer and comparing this with the manufacturer`s documentation for the diameter of piping in the system. If this is lower than advertised then the pump is not performing correctly and may need to be repaired or replaced.
Smaller repairs like replacing a rubber door gasket on a front-loading machine or fixing a jammed drain pump are likely to be less expensive and are worth fixing so that you can keep your washing machine going.
Pump repair is necessary to reduce the operating costs of pumping and to prevent corrosion in the pumps. Pump repair may be performed when there are changes in sound of a running pump, abrupt changes in bearing temperatures, and seal chamber leakage of a pump.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

Oil appears to have come out of the oil filler cap. Is this a sign of overfilling the oil, or something else?
ANSWER : Id definitley say its over filled. try checking the dipstick

Read Full Q/A … : Garden

What oil do i use in the pump? The oil is milky and needs changing.
ANSWER : Well you can use direct recommended from Ace Hardware see link.

http://www.acehardware.com/product/index.jsp?productId=1340266

They recommend 250 hours, but i’d change more often, like you said when it’s milky. If it begins to get water in the oil sooner, that indicates your piston to crankcase seal is beginning to leak.

Read Full Q/A … : Garden

Leaking oil through the casing – Karcher K2.26 Electric Power Washer
ANSWER : Up end the unit and get to the sump plate of the pump
remove the big screws that hold it on and there is a big”O” ring that is the seal
replace that “O” ring and use silastic blue sealer and reassemble it

Read Full Q/A … : Garden

What type of oil goes into the pump – Honda Pressure Washer PSI 3000
ANSWER : YOU NEED AN OIL THAT IS THIN & CAN COPE WITH HIGH TEMPERATURES.
I USE & RECOMMEND HYDRAULIC OIL

Read Full Q/A … : Garden

How to replace a oiler on a stihl chainsaw ? – Stihl Service Manual for 031AV Chainsaw with Parts List
ANSWER : Remove the worm, sealing ring and washer, loosen the pan head screws on the oil pump and replace. Check if the gasket is re-usable.

Read Full Q/A … : Garden

What kind of oil does it use for Remington 16’electric saw.
ANSWER : Use any bar and chain oil. Can be bought at most big-box-stores (Home Depot, Lowes) or stores that sell outdoor power equipment. Don’t use motor oil, you’ll have a mess when you store the saw.

Read Full Q/A … : Garden

What type of oil is used to fill the a FAIP PV93501 pump and what quanity.
ANSWER : I don’t know about that brand of power washer.We used several types of power washers over the years, and they each called for 20 or 30 weight non-detergent oil in the pump. SAE 20 or SAE 30The pump oil comes about half way up inside the pump.The engine oil is 10W30Do not turn a power washer on its side or upside down or oil will run into carburetor.

Read Full Q/A … : Garden

WATER COMING OUT AT BOTTOM OF WASHER – Karcher K2.26 Electric Power Washer
ANSWER : Dear Sir,
In this case the seals surrounding the pistons (3 in number)..are faulty.
You can open the cover first ( by using a TORX T15 screw driver). Start machine in this way with all attached…( never run a power washer with out water and never store a power washer with pressure in it). When you start machine with out cover you can more easely see from where water is coming out. Mostly the case will be that water is coming out from between the head and the bottom part of machine. If water went into the bottom part…then the oil is ruined also.
So this case needs that all seals to be changed. One must inspect the pistons….because if the pistons are scrathed and pitted…then it is useless to put new seals. Thus new pistons must be put with new seals…and other gaskets renewed.
fulltech.

Read Full Q/A … : Garden