Power AHS 600-24 ST 600 W Hedge Trimmer BOSCH

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

Visually inspect the blades and confirm there is no debris stopping the blades from moving. If there is debris ensure the machine is powered off when removing any blockages. Check the blades for any damage as a damaged cutting blade could cause the machine to stop working.
A clogged carburetor is most commonly caused by leaving fuel in the hedge trimmer for a long period of time. Over time, some of the ingredients in the fuel may evaporate, leaving behind a thicker, stickier substance. This sticky fuel can clog up the carburetor and cause the engine to stall or run roughly.
If you notice the branches you`re working on are being cut unevenly or are frayed, this is an sign that the blades need to be sharpened. Sharpening the blades may solve this issue without having to replace any parts. Another issue that you may encounter is bent teeth on your trimmer`s blades.
That means it`s not holding the blades securely against the clipper which will cause it to drag here. Also, make sure your screws are tight on your hinge. A lot of times the screws will back out and once again it`s not holding the blades properly on the clipper which will cause it to drag.
The clutch engages the clutch pads to spin the trimmer head. If the clutch assembly is defective, the clutch will not disengage the clutch pads, and the trimmer head will continue to spin, even at low speeds. If the clutch is defective, replace it. (Note: some string trimmers do not have a clutch.
With a severed cord, your hedge trimmer is virtually worthless. With a small amount of money and a little ingenuity, however, you can repair the cord and have the trimmer running. If the cord left attached to the trimmer is long enough to be useable, then you simply can add a new plug to its end.
If your clipper blades are still pulling the hair, you will need to replace your blades or alternatively have them sharpened.
For best operation and longer blade life, lubricate the hedge trimmer blade with a lightweight machine oil before and after each use.
This can be due to corrosion, scratches or general wear. As a result, the cutting edges of the cutter comb of your blades are no longer sharp, reducing their ability to cut. Sharpening the blade is required to reface the cutting surfaces restore these sharp edges.
The blade drive is generally the biggest culprit in why freshly sharpened blades won`t cut. The blade drive holds the socket in place to drive the cutter evenly along the deck of the blade. Over time the drive/lever edges wear down and become rounded or worn which affects the performance of the clipper blade.
The possible causes of a lawn mower blade spinning but not cutting grass include a damaged or wrongly installed blade, a dull blade, or damaged lawnmower tires. Other possible reasons can be improper tire pressure, a clogged deck, or a broken mower belt.
If your clipper blades are still pulling the hair, you will need to replace your blades or alternatively have them sharpened.
The possible causes of a lawn mower blade spinning but not cutting grass include a damaged or wrongly installed blade, a dull blade, or damaged lawnmower tires. Other possible reasons can be improper tire pressure, a clogged deck, or a broken mower belt.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

Blade moves back and forth,but won’t cut anything
ANSWER : Check the bolts or screws holding the blades together are tight but not so tight that they cant move. Ensure blades are sharp.

Blades wont move when power connected. Stripped it down. Motor is fine. I think it must be the gears attached to the blade unit
ANSWER : Either the gears, OR SOME machines have a “CENTRIFUGAL CLUTCH” [a safety feature] between the engine and the blades.

IF your machine has this feature, then it’s possible that the clutch has worn out and is slipping so badly that the blade won’t move.

Not cutting properly. blades seem to be out of sync.
ANSWER : Hi
try to spray oil the blades
if not helping
take the machine to be seviced you might need to sharpen the blades.

Trimer buing Question
ANSWER : Double position trimmers
For extended reach while on the ground, a double position trimmer avoids you having to climb up high by allowing you to adjust the handle into a right angle to the blades for a level cut across the top of the hedge.
Clippings collector
As you trim your hedge, collect those stray cuttings in a clippings collector for a neater finish.
Automatic cut out
An important safety feature, this automatically switches off the hedge trimmer once the trigger is released.
Hand guard
For reassuring safety, a hand guard will protect you from the moving blades and from falling cuttings as you work.

Baldes locked up – Remington At3017b Hedge Wizard
ANSWER : Ensure blades are sharpened. If there are burs on blades they can seize.Blades should be lubricated with WD40 , waste oil or other lubricant.The bolts holding the two blades together shouldn’t be too tight.

Engine runs great, accelerator responds perfectly, but the blades stopped moving. Any ideas?
ANSWER : Ensure blades are sharpened. If there are burs on blades they can seize.Blades should be lubricated with WD40 , waste oil or other lubricant.The bolts holding the two blades together shouldn’t be too tight.

How to sharpen stihl gas power trimmer
ANSWER : Sharpen with a flat file. Its a long process as each tooth has 2 cutting edges. There are companies that will do this properly at cost.

Corona professional long-handled hedge shear
ANSWER : Try tightening the nut and bolt that hold the shears