age but nothing…what would the next step be?? Tks
17.5 hp 42 in. Deck Lawn Tractor – CA Model
Experienced gardeners share their insights in answering this question :
When you say nothing happens…is the PTO engaging? You said that you already checked the belts…if none of these are off…you maybe looking at a new PTO clutch.www.nnyparts.com
How to Identify and Fix Common Gardening Problems ?
We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :
If the PTO clutch is not getting power, if the clutch solenoid is defective, or if the clutch is worn out, the lawn mower blades will not engage. The PTO clutch is not repairable—if the clutch is defective, you must replace it.
Belt-the number one cause for your blades not to engage is that your belt is either stretched or loose causing it to slip or fall off completely. Belt could have snapped also. When you are trying to process too much grass/leaves they could pack up under your deck and push off your belt.
The reasons why mower is not moving forward or reverse is that the battery is dead, or due to clogged fuel line. Additionally, malfunctioning transmission, or a broken drive belt, also a faulty spark plug, even when friction wheel isn`t in contact with the friction plate, or damaged Tires.
An improperly routed belt can cause the engine to die when the blades are engaged. To check belt routing, lower the deck to its lowest setting and remove the belt guard by the drive pulley. Next, lift the belt over the pulley and remove the pins that support the deck at the rear.
Failure of any mechanical component, a broken hose, or clogged filter will cause tractor hydrostatic transmission problems. But the most common issue will be the oil itself. In the transmission section of your operator`s manual, you`ll find a section that covers oil viscosity.
Your lawn mower`s piston can seize if the mower stands for a long time in wet conditions or if you forget to put oil in the crankcase. You may be able to free the piston by removing the spark plug and manually rocking the blade.
The blade belt spins the blades to cut the grass. A worn or broken drive belt won`t spin the cutting blades so your mower won`t cut the grass. A worn blade belt can also cause mower deck vibration or uneven cuts. Examine the blade belt regularly and replace it if it`s worn or broken.
If the PTO clutch is not receiving power, the clutch solenoid is defective, or the clutch itself is worn out, the blades will not engage. Since a PTO clutch is not repairable, you will need to replace a broken or worn out clutch with a new one.
Powershift PTO engagement problems could be from blocked hoses or fittings, bad connections or ground or the solenoid. Mechanical PTO engagement problems could originate from low air pressure, improper cable installation or back lash too tight.
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
Have a Craftsman 26 hp, 48″ mower…mower starts runs but when I try to engage the blades nothing happens. Checked all the belts, ck for blockage but nothing…what would the next step be?? Tks
ANSWER : When you say nothing happens…is the PTO engaging? You said that you already checked the belts…if none of these are off…you maybe looking at a new PTO clutch.www.nnyparts.com
Read Full Q/A … : 17.5 hp 42 in. Deck Lawn Tractor – CA Model
I need a operating maual for a craftsman riding mower 28990
ANSWER : Sears Manage My Life has the Operator’s Manual: . Click on “Craftsman Lawn, Tractor” to get to the manual page.
Read Full Q/A … : 17.5 hp 42 in. Deck Lawn Tractor – CA Model
Craftsman DYT 4000, 24 hp 48″ deck. While I was mowing, the blades stopped turning, started again, and then stopped. I shut down, all looked OK, tried to start and nothing. No click, nothing. Any ideas?
ANSWER : There is a fuse in engine compartment that might have blown causing the engine or blades not to start but what probably happened was something got caught in the blades check under the deck & see if there is & also try spinning blades by hand & see what happens
Read Full Q/A … : 17.5 hp 42 in. Deck Lawn Tractor – CA Model
Slack in belt from motor to mower blades – Craftsman 24 Hp 48" Deck Yard Tractor
ANSWER : There should be some so the blades are not constintly turning. If the attacment clutch is engaged and the blades do not turn, either the tentioner is frozen in place and not applying tention on the belt, the belt is routed wrong it is too large for the tractor.
Read Full Q/A … : 17.5 hp 42 in. Deck Lawn Tractor – CA Model
PRIMARY BELT SIZE – Craftsman 24 Hp 48" Deck Yard Tractor
ANSWER : I WOULD SUGGEST HIGHLY YOU GET REPLACEMENT BELTS FROM SEARS . THE AUTOMOTIVE BELTS ARE IN ONE INCH INCROMENTS SEARS BELTS ARE IN HALF INCH .. GET YOUR MODEL NUMBER AND CONTACT YOUR LOCAL SEARS OR K MART . FOR THE PROPER BELT ! .. JUST THE WAY IT IS WITH CRAFTSMAN MOWERS … SORRY ….
Read Full Q/A … : 17.5 hp 42 in. Deck Lawn Tractor – CA Model
Runs but blades wont activate – Craftsman 21 Hp 42" Deck, Ys 4500 Lawn Tractor
ANSWER : The drive belt on my YS 4500 keeps coming off. You need to put it back on, by hand, if it’s not too hot. You just need to find the route of the belt.
Read Full Q/A … : 17.5 hp 42 in. Deck Lawn Tractor – CA Model
We have a brand new Craftsman 26 HP, 54″ deck lawn tractor, our problem is that the belt that turns the blades keeps slipping off, HELP!!!!
ANSWER : Adjust the tension on the idler pully or refer to your manual
Read Full Q/A … : 17.5 hp 42 in. Deck Lawn Tractor – CA Model
I need the belt digram for a 50″ craftsman lawn tractor, it has two belts on the deck.. any help?
ANSWER : You need exact model numbers. Go to www.searspartsdirect.com put in your model number and see parts list. Go to the right hand side of page and click on manuals.
Read Full Q/A … : 17.5 hp 42 in. Deck Lawn Tractor – CA Model
