How to Identify and Fix Common Gardening Problems ?
We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :
Q: How do I mix gas and oil? A: Mix 3.2 ounces of Poulan 2-cycle air cooled engine oil to one gallon of fresh unleaded gasoline to obtain the recommended 40:1 fuel to oil ratio.
Poulan engines are designed to run best on 87-octane regular unleaded gasoline — avoid using diesel fuel and E85.
A single fuel pipe runs from the tank, under the floor of the car to a mechanical pump on the engine. The pump delivers fuel to the carburettor. Whenever you check fuel pipes, disconnect the battery to prevent stray sparks igniting petrol or petrol vapour.
Most vehicles have rubber fuel hoses connecting the fuel pipes on the chassis to the fuel pump or carburetor on the engine. Rubber hoses are flexible and can be cut to length as required, but they have a tendency to perish over time and can rub through if not properly secured.
Oil mix ratios explained
If your manufacturer recommends a 50:1 fuel/oil mix, it means you need 50 parts of gas to one part two-stroke oil. To mix one gallon of fuel at 50:1, add 2.6 ounces of two-stroke oil to one gallon of gas, as shown in the chart below.
For a 50:1 ratio of gas to oil, use 2.6 fluid ounces of oil per gallon of gas. For a 40:1 mixture, use 3.2 fluid ounces of oil per gallon of gas.
STIHL recommends that customers use a minimum of 89 octane fuel. If a customer chooses to use a 91 or 93 octane fuel, no damage to the engine will result. However, using an 87 octane fuel could lead to serious engine damage.
You can find Poulan Pro products both in-store and online at home improvement retailers, hardware stores, and mass merchants all over North America. We are here to help you tackle… ANY YARD.
The (clear) fuel intake line runs from the top of the carburetor (straight nipple) and goes to the short post on the back of the primer bulb. The return line (blue) comes from the long post on the back of the primer bulb and goes into the bottom of the fuel tank.
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
I need a diagram of how to route the throttle line on my Poulan 225 Pro chainsaw. Where can I get one?
Gas line routing – Poulan Wild Thing 2375 18" Gas Chain Saw 2.5 Cuin
Try going to a local hardware store and ask them about gas routing for chainsaws. If that doesnt work then I suggest to send the chainsaw back and have them replace it.
Poulanproleafblower not primeing
Either your fuel
is broken inside the tank or your carb is blocked up inside. Empty the fuel tank and look inside and see if you fuel inlet line has a little plastic or metal filter on the end. *(this is called a “clunk”) The clunk keeps the fuel line in gas no matter which way you have the blower tilted. Chances are you will see the clunk just laying in the bottom of the tank with whats left of the fuel line still attached. If the fuel line and clunk are intact then your need to get a diagram of the carb and do a dissembly and cleaning. The carbs have tiny screen filters which jam up with debris and gelled fuel. So a rebuild kit with new filter would be a good thing to get if your carb is cruddy. You can look online at Poulanpro and see which kit you need to buy. They are 10-15 bucks usually. New fuel lines is also a good idea if you are going this deep into the unit. Be safe and good luck!
I need to replace the fuel lines in my poulan model 1950 14″ saw. Unfortunately the lines were rotted off already and I can’t tell where they came off. Could you tell me where they fit?
Try at eReplacementParts.com : Power Tool Parts and Tool Repair Diagrams.If you need more help come back.Post / thumbs / testimonial are welcome!
Is it straight gas or mixed? – Poulan Pro 14" Gas Chainsaw 33CC P3314
It uses a gas/oil mix. 40:1Hope this helps.
How do I replace the fuel line for a Poulan ppbp30?
Open the top of the machine to access the carb, Normally it is easily done with needle nose pliers.
Fuel line diagram – Poulan P3314 14-Inch 33cc 2-Cycle Gas-Powered Chain Saw
Here is the way to hook up the fuel lines
Note: I put it together outside of the saw so you could see how it is hooked up. Fuel filter/pickup >>to>> Inlet on carb >>to>> Outlet of carb >>to>> to inlet on Primer bulb(shorter post) >>to>> Outlet of primer(longer post) >>to>>Fuel tank (usually has a retainer in tank to prevent fuel line from coming out.)
Poulan te 450 cxl fuel lines need routed correctly two line both in tank one to fuel filter other line?
Other line is just left open like to send gas back from the carb.