Craftsman
I need to know how to route the fuel lines for a poulan prolink pbb330 trimmer
How to Identify and Fix Common Gardening Problems ?
We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :
The (clear) fuel intake line runs from the top of the carburetor (straight nipple) and goes to the short post on the back of the primer bulb. The return line (blue) comes from the long post on the back of the primer bulb and goes into the bottom of the fuel tank.
A typical fuel system
A single fuel pipe runs from the tank, under the floor of the car to a mechanical pump on the engine. The pump delivers fuel to the carburettor. Whenever you check fuel pipes, disconnect the battery to prevent stray sparks igniting petrol or petrol vapour.
A: Mix 3.2 ounces of Poulan 2-cycle air cooled engine oil to one gallon of fresh unleaded gasoline to obtain the recommended 40:1 fuel to oil ratio. Over a period of time oil will separate from gasoline.
Most chainsaws have two fuel lines – one that feeds fuel into the carburetor and a return tube that allows unused fuel to flow back into the chainsaw gas tank.
The carburetor might be clogged. A clogged carburetor is often caused by leaving fuel in the chainsaw for a long period of time. Over time, some of the ingredients in the fuel may evaporate, leaving behind a thicker, stickier substance. This sticky fuel can clog up the carburetor and cause the chainsaw engine to stall.
The main colors used in ISO 14726 are as follows:
Blue – Fresh water. Brown – Fuel. Green – Sea water.
Metal, Rubber, Braided, or PTFE Lined
Fuel Lines can be made from many different materials. If you plan to race, be sure to check the rule book for your track or sanctioning body. Using the right material the first time will save you time, money, and headaches.
It`s hard to deny that rubber hose is still a popular choice for many homebuilt fuel systems. It is relatively inexpensive and very easy to install. Compared to other options such as rigid aluminum tubing, it has one major shortcoming: It has limited life and cannot be considered a permanent part of the airframe.
Engine misfires, hard starting, and stalling
A fuel leak due to a worn or damaged hose can cause the vehicle to experience issues such as misfires, hard starting, stalling, and can even prevent the vehicle from running at all.
Material: Metal fuel lines are made from materials such as steel or aluminum, while rubber fuel lines are made from rubber or other elastomeric materials. Braided fuel lines are typically made from a metal or synthetic fiber braid that is wrapped around a rubber or other elastomeric core.
The return line should direct fuel close to the bottom of the tank and away from the pickup.
Most modern chainsaws, string trimmers, leaf blowers and other small-engine two-stroke equipment recommend a 50:1 oil mix ratio, but some recommend 40:1 and older two-stroke equipment might even call for 32:1.
For a 50:1 ratio of gas to oil, use 2.6 fluid ounces of oil per gallon of gas.
Most chainsaws have two fuel lines – one that feeds fuel into the carburetor and a return tube that allows unused fuel to flow back into the chainsaw gas tank.
Many of today`s chainsaws will come with felling marks. Similar to the sight on a gun, these lines will help the operator align the cut with the direction the tree will be felled.
Many of today`s chainsaws will come with felling marks. Similar to the sight on a gun, these lines will help the operator align the cut with the direction the tree will be felled.
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
Fuel line diagram – Poulan P3314 14-Inch 33cc 2-Cycle Gas-Powered Chain Saw
ANSWER : Here is the way to hook up the fuel lines
Note: I put it together outside of the saw so you could see how it is hooked up. Fuel filter/pickup >>to>> Inlet on carb >>to>> Outlet of carb >>to>> to inlet on Primer bulb(shorter post) >>to>> Outlet of primer(longer post) >>to>>Fuel tank (usually has a retainer in tank to prevent fuel line from coming out.)
Read Full Q/A … : Craftsman
Poulanproleafblower not primeing
ANSWER : Either your fuel
is broken inside the tank or your carb is blocked up inside. Empty the fuel tank and look inside and see if you fuel inlet line has a little plastic or metal filter on the end. *(this is called a “clunk”) The clunk keeps the fuel line in gas no matter which way you have the blower tilted. Chances are you will see the clunk just laying in the bottom of the tank with whats left of the fuel line still attached. If the fuel line and clunk are intact then your need to get a diagram of the carb and do a dissembly and cleaning. The carbs have tiny screen filters which jam up with debris and gelled fuel. So a rebuild kit with new filter would be a good thing to get if your carb is cruddy. You can look online at Poulanpro and see which kit you need to buy. They are 10-15 bucks usually. New fuel lines is also a good idea if you are going this deep into the unit. Be safe and good luck!
is broken inside the tank or your carb is blocked up inside. Empty the fuel tank and look inside and see if you fuel inlet line has a little plastic or metal filter on the end. *(this is called a “clunk”) The clunk keeps the fuel line in gas no matter which way you have the blower tilted. Chances are you will see the clunk just laying in the bottom of the tank with whats left of the fuel line still attached. If the fuel line and clunk are intact then your need to get a diagram of the carb and do a dissembly and cleaning. The carbs have tiny screen filters which jam up with debris and gelled fuel. So a rebuild kit with new filter would be a good thing to get if your carb is cruddy. You can look online at Poulanpro and see which kit you need to buy. They are 10-15 bucks usually. New fuel lines is also a good idea if you are going this deep into the unit. Be safe and good luck!
Read Full Q/A … : Craftsman
Where does the duck valve go in a Poulan 2150 chainsaw? Iam trying to replace the fuel lines . Does it go in the fuel tank? I need a diagram of the fuel lines.
ANSWER : Is your fuel cap missing the hold down that keeps it from falling out of the tank.if the keeper is missing from fuel cap, the valve goes in the cap.if the cap is together then it just sticks in the fuel tank hole in the top…… hope this helps,let me know……………..
Read Full Q/A … : Craftsman
I have a poulan 305 pro chain saw were do the 2 fuel lines go?
ANSWER : Find your model nuber here:
Poulan.com
http://www.ordertree.com/modelinfo/POULAN-WEED-EATER/75.59.html
The drawing containing your fuel system is as good as it gets. If you need more help contact PoulanPro.com. HTH
Lou
Poulan.com
http://www.ordertree.com/modelinfo/POULAN-WEED-EATER/75.59.html
The drawing containing your fuel system is as good as it gets. If you need more help contact PoulanPro.com. HTH
Lou
Read Full Q/A … : Craftsman
I need to replace the fuel lines in my poulan model 1950 14″ saw. Unfortunately the lines were rotted off already and I can’t tell where they came off. Could you tell me where they fit?
ANSWER : Try at eReplacementParts.com : Power Tool Parts and Tool Repair Diagrams.If you need more help come back.Post / thumbs / testimonial are welcome!
Read Full Q/A … : Craftsman
Replaceing fuel line in polan 3300 chain saw – Poulan Pro 42CC 2 Cycle Chainsaw, 18"
ANSWER : Hi owjbhend…
Use a piece of wire and insert it into the fuel line, then bend a hook in the end and hook it over the end of the fuel line…lubricate the fuel line with some vaseoline very lightly…about the first one inch of the fuel line and then use your fingers to start the fuel line into the tank, once you have the fuel line in the tank give enough to hook the fuel filter to and so it can be dropped back into the tank.
Below is a drawing of how to route the fuel lines.
Please take time to rate me thumbs up
Please take time to rate me thumbs up
Use a piece of wire and insert it into the fuel line, then bend a hook in the end and hook it over the end of the fuel line…lubricate the fuel line with some vaseoline very lightly…about the first one inch of the fuel line and then use your fingers to start the fuel line into the tank, once you have the fuel line in the tank give enough to hook the fuel filter to and so it can be dropped back into the tank.
Below is a drawing of how to route the fuel lines.
Please take time to rate me thumbs up
Please take time to rate me thumbs up
Read Full Q/A … : Craftsman
How to get manual or diagram for fuel lines
ANSWER : If that is a return fuel line yes
Read Full Q/A … : Craftsman
Need a diagram of the fuel lines on a poulan 2150. what lines go where?
ANSWER : You can View a Diagram of the Chainsaw here http://hayward.arinet.com/scripts/EmpartISAPI.dll?MF&app=ASP⟨=EN&TF=Mainfram…
Select the Catalog Poulan/Weed Eater. Then Select Poulan. Then Select Gas. Then Select Saw. Then Scroll Down to your Model Saw i.e 2150.
Regards
Marc
Read Full Q/A … : Craftsman
