ZR10926 16 Chain Saw

How do i start my homelite gas chainsaw
model 350x
Experienced gardeners share their insights in answering this question :
Put the choke on, and if it has a primer bulb, push 3 times, then crank it.Jim

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

If your electric chainsaw won`t start, try examining it for these issues: Not pressing the safety button at the same time as the trigger. Tripped electrical breaker (for corded chainsaws) Frayed or damaged electrical cord (for corded chainsaws)
Just let the saw sit for 30 min and the excess gas will evaporate. Remove the spark plug, dry it, crank over the engine a few times to dry the cylinder. Now refit the plug and try again. Set the switch to “On”, set throttle to fully open, set choke to “Off” and crank over the engine.
If your STIHL chainsaw is going to have a problem, it`s likely to be with a worn carburetor, bad spark plugs, loose fuel hoses, or clogged fuel lines. You should also inspect the fuel intake system and ensure that there are no compression issues.
A dirty carburetor, bad gasoline and low-quality two-stroke oil that creates deposits all contribute to chainsaw starting problems.
One tell-tale sign that a chainsaw has flooded is the smell of fresh petrol near the muffler. To ascertain whether this is indeed the problem, simply disassemble the part, pull the starter cord as if you were switching on the engine, then dry it, reassemble it and try switching it on again.
A dirty carburetor, bad gasoline and low-quality two-stroke oil that creates deposits all contribute to chainsaw starting problems.
With the choke in the “off” position, pull the engine`s crank cord through again. The engine should start in 1 to 3 pulls. Try it first without using the throttle control—unless recommended by the manufacturer.
What Causes Chain Saw Kickback? There are two circumstances that can cause kickback when using a chain saw. The first occurs when the moving chain at the tip or the nose of the guide bar strikes an object. The second situation is when the wood closes in, pinching the saw chain in the middle of the cut.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

Toro clear won't start – Toro Power Clear 621 R
ANSWER : Bad gas , plug ,air filter , no spark ck all need all 3 to start

Read Full Q/A … : ZR10926 16 Chain Saw

Does not run, will start with starting fluid – Mantis 2-Cycle Tiller
ANSWER : You should never use starting fluid on this model.

Add a couple of ounces of 100% acetone (available at Walmart) to some fresh fuel. Attempt to start for several pulls. Let sit for several minutes and repeat until it sounds like it wants to run.

Then watch this video and do it:

http://www.alamia.us/mantis_parts_s/148.htm

Read Full Q/A … : ZR10926 16 Chain Saw

Strimmer wont start plug very dry when i remove it?
ANSWER : Sounds like the gas is not getting to the cylinder—remove carb and disassemble–make sure all jets are clear and the float valve moves freely.

Read Full Q/A … : ZR10926 16 Chain Saw

Why do I have hard time starting my ariens snowblower when cold?
ANSWER : Does it have a primer bulb been seeing a lot of the bulbs with cracks

Read Full Q/A … : ZR10926 16 Chain Saw

Tines continue to work with out touching safety or throttle. they engage as soon as I start the engine.
ANSWER : Remove H (high) L (low) plastic caps to allow you to further adjust the flow and you will be going. H (red) further out about 11 threads exposed and L (low) about 8 exposed; adjusting the low side will stop the tines, but remove tines before making any adjustments, thanks

Read Full Q/A … : ZR10926 16 Chain Saw

Mower won’t start. Toro mower..engine won’t turn over. Cleaned sparkplug…checked air filter..weather cool. Followed instructions for cold engine…prime witrh three pushes of the bulb..wnon’t even hint at a start..
ANSWER : Something everyone over looks is oil. Did you check the oil? You seemed to mention everything else but. If you have a low oil switch with low oil it will not start

Read Full Q/A … : ZR10926 16 Chain Saw

<!– from fixya rte –>Rj19lm plug gap for a 195cc 4cyl lawnboy – Lawn-Boy lawnboy" Mower Blade 21"
ANSWER : As a starting point in my shop i always use 0.30 in. For all my mowers

Read Full Q/A … : ZR10926 16 Chain Saw

I forgot to add oil to my toro ccr powerlite e. should i remove the gas and start all over again?
ANSWER : !!!!!! dran the gas put in the neww mix gas and pray for the best

Read Full Q/A … : ZR10926 16 Chain Saw

My name is June Strandberg, and I am a florist and gardener in San Francisco. I have been working in the industry for five years, and I love helping people find the perfect floral arrangement for their special occasions. I am also skilled in troubleshooting and fixing gardening tools, so if you are ever having trouble with your tools, please don't hesitate to reach out to me.