Garden

The first pull of the day is fine but after running it for about ten minutes it acts like it wants to cut off if you let off from spaying. When you do let off from spraying it does cut off. then i go to pull and she wont let me.
i pulled both my for arms. That if the piston is at the bottom. but if its top dead center i can start it agin. anyways when it gets warm its hard to start almost like it has ungodly amount of pressure/ compression.

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

A clogged carburetor is most commonly caused by leaving fuel in the pressure washer for a long period of time. Over time, some of the ingredients in the fuel may evaporate, leaving behind a thicker, stickier substance. This sticky fuel can clog up the carburetor and cause the engine to run stall.
Gas-powered pressure washers have a thermal release valve that releases water from the pump when it reaches a specific temperature to keep the pump from overheating. When the valve is open, new, cooler water is introduced into the pump and then closes when the temperature is brought down.
Water leaking from a loose connection can cause the unit to cycle on and off. Verify if the pressure hose has an O-ring at the connection. If missing, this will also cause the unit to cycle on and off. While the unit is running look for any water leaks that may cause the unit to turn back on.
The engine of your pressure washer may rev sporadically because it is experiencing an intermittent blockage of the air that it needs to function properly. The first thing that you should do is to check the air filter for clogs caused by debris or dirt. Clean out any clogs that you find and the erratic revving may stop.
How Do I Tell If My Unloader Valve is Bad? In most occurrences, the first symptom of an unloader valve going bad is no pressure from the wand when the trigger is pressed. This happens when the unloader valve gets stuck open and does not allow water to enter the hose and trigger.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

My Honda 2600 psi power washer will not pull to start. It was running great then I allowed the neighbor to borrow it. He ran the washer till it was out of gas and proceeded to refuel and at this point it would no longer start. The pull cord is out about 4-6 inches out and I am concerned about taking the casing off myself.

Fearing that it may throw more off on the unit. If i take the casing off are there any spring loaded parts that will dismount?

What should I do? Spark Plug? Turn wrenches?

Please let me know

ANSWER : You should be fine to take the recoil off, there shouldn’t be anything that shoots out at you. You might want to check the oil level on the engine, many of the Honda engines won’t start unless there is enough oil in them. If your oil level is fine, check to make sure that your motor is getting spark.

Read Full Q/A … : Garden

What kind of soap do I need to use? – Honda Black Max 2600 PSI Pressure Washer
ANSWER : I suppose that would be dependent upon what you would be cleaning eh?If moss on white siding use a bleach solutionOtherwise for general cleaning I prefer “simple green” — you may cut it up to ten times with water….Best regardsCk

Read Full Q/A … : Garden

Honda powwer boss 3000-whenyoupull the handale to spray it kills the engine
ANSWER : Sounds like the unloader (regulator). Try removing the nozzle, the pull the trigger with the engine running. If motor is still running then it could be the Unloader malfunctioning. If you require a new one try a bypass system for the unloader. The bypass will help save the life of the unloader.

Read Full Q/A … : Garden

Need help in getting Honda engine on NorthStar pressure washer to run.
ANSWER : Could be low water pressure I have found.Also, I purchased a can of “stuff” at Lowes today which allows you to circulate a liquid substance which lubricates the pressure pump….the pump could be frozen up…I have a rotating nozzle which I bought…and it had frozen up…this stuff works

Read Full Q/A … : Garden

<!– from fixya rte –>Rope pull start is stuck, won't pull out – Honda Black Max 2600 PSI Pressure Washer
ANSWER : Check the oil level, if it’s very low or burnt then it may have siezed up internally.
It could also be that be that the cylinder is filled with oil or fuel.
if the washer was tipped over the fuel or oil may have migrated in to the piston combustion area.

Read Full Q/A … : Garden

Pressure washer with 5hp Honda will ONLY run with choke on
ANSWER : It sounds like it has been tipped or too much oil has been put in. This would explain the oil in the air filter. First check the oil level. Then you need to clean the oil out of the carburetor. It is dirty or plugged and that is why it only runs when choked. You can try a spray-in carb cleaner but the best thing is to remove it (if you are handy enough) and soak it in varsol for 24 hours. Good luck

Read Full Q/A … : Garden

Got spark and gas can’t get it running what is the conpression supposed to be
ANSWER : I have a honda power washer EXHA2424, I replace new spark plug, new gas., cleans the cabureetor, and it still won’t start please advice me what to do

Read Full Q/A … : Garden

Engine runs but no pressure – Honda Pressure Washer PSI 3000
ANSWER : Many people forget to shut down the “CHOKE” after a cold start up.

Read Full Q/A … : Garden