and there is power coming in but not passing this one little white bot with some wire hook to it. it like the wires or not hook up right. if you can send me a wire digrem to me it would be helpful.
Garden
How to Identify and Fix Common Gardening Problems ?
We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :
If the pressure washer does not start, then the first thing to check is the fuse in the plug. The reading you`re looking for is the same as it would be when connecting the two probes of the multimeter together (as you can see in the example of this video, this fuse is actually fine).
It Can Harm The Unit
Without water to cool and lubricate it, the pump will work harder than it should, causing it to wear down quickly. This can happen even with just a few seconds of running the pressure washer without the water being turned on.
The pressure washer hose will fill with water, so it is important to purge the system of excess air before starting the unit. Simply squeeze the trigger on the gun and the air will release.
The fuse is inside the plug… may have to remove both covers.. However, if you get a red light, it is not the fuse, and the plug can go bad if water gets in, in which case you may have to replace it..
There are a variety of reasons as to why your pressure washer may not start. Some of these include, a dirty air filter, lack of or old fuel, problems with the spark plug wire`s connection or a bad spark plug, water in the fuel or an excessively rich fuel mixture, or the choke is in the ON position.
A clogged or improperly sized filter reduces the amount of liquid to the pump inlet, which can cause cavitation and even severe pump damage. Reduced inlet flow results in reduced flow to the system, which works to reduce system pressure as there is less resistance to the lower flow being produced.
The pressure washer hose will fill with water, so it is important to purge the system of excess air before starting the unit. Simply squeeze the trigger on the gun and the air will release.
The fuse is inside the plug… may have to remove both covers.. However, if you get a red light, it is not the fuse, and the plug can go bad if water gets in, in which case you may have to replace it..
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
Has no pressure, builds up when not holding trigger on gun, but when i press trigger shoots of with pressure the nothing just water comes out.
ANSWER : Bad pump
Read Full Q/A … : Garden
Electric pressure washer xte 1650 no power coming in to the moter. i put a new fuse init and still no power to the moter. i put a tester to it and there is power coming in but not passing this one little white bot with some wire hook to it. it like the wires or not hook up right. if you can send me a wire digrem to me it would be helpful.
ANSWER :
Read Full Q/A … : Garden
I have used the McCulloch (FH180A) three times over the course of two years. On my fourth use the pressure washer just surged on and off and I would get a tiny spray from the gun each time it surged. In other words it would do nothing. Please help… very frustrated. Thanks
ANSWER : Sounds like the problem could be low input water flow or pressure. There could be crud on the intake where you hook up the garden hose, there could be some other sort of blockage. Try hooking it up to the hose and pull the trigger (with the power switched off) and wait to see if water comes out the tip. Also look at the tip(s) themselves. sometimes a piece of crud gets into the hose and then clogs the tip.
Read Full Q/A … : Garden
Low pressure Will not keep pressure
ANSWER : Faulty pump. check each valve for obstruction or fault
Read Full Q/A … : Garden
1750 psi Electric Pressure Washer: My pressure washer is losing pressure and is pulsa…
ANSWER : If the pressure washer is pulsating then that is a sign of check valve failure. You may be able to clean of replace the check valves. Replacing the head is the wrong way to go. This is completely unnecessary. If you can tell me the model number of your pressure washer then I can assist you better in pointing you in the right direction.
Read Full Q/A … : Garden
Need help in getting Honda engine on NorthStar pressure washer to run.
ANSWER : Could be low water pressure I have found.Also, I purchased a can of “stuff” at Lowes today which allows you to circulate a liquid substance which lubricates the pressure pump….the pump could be frozen up…I have a rotating nozzle which I bought…and it had frozen up…this stuff works
Read Full Q/A … : Garden
Power washer works perfect for 10- 15 minutes then blows fuse. Put in new fuse straight away and works fine again for another 10-15 minutes.
ANSWER : These machines can have issues such as you have explained if they are run off from an extension cord or if they are really far from the breaker box. They have this issue because the amount of amps that are going to the machine aren’t enough for the motor to operate efficentially so the motor in turn gets hot and blows the fuse or the breaker.
Another issue could be is that the nozzle is being restricted to much and is causing the motor to work harder than what it should and is causing the machine to over heat. This in turn would cause the motor to blow a fuse or a breaker.
Read Full Q/A … : Garden
How do i hook up a hose to the power washer – McCulloch FHH18A Electric Pressure Washer
ANSWER : Have you tried looking on the back of the machine?
Read Full Q/A … : Garden
