20 hp 42 in. Deck Lawn Tractor – CA Model
Correct drive belt size?
Experienced gardeners share their insights in answering this question :
You need to post the 917.xxxxxx model number for some one to help you. There are about 10 different belts that fit different 42″ Craftsman mowers.
You could also go to www3,sears.com and put in the same 917.xxxxxx model number and look up the part number. You do not want to buy a belt just by the size alone but must use one that is made for the machine application. The cheaper ones that you pick up in the local hardware store etc. like a 3Lxxx or 4Lxxx are made for low horsepower electric motors and will not last on your lawnmower.
You could also go to www3,sears.com and put in the same 917.xxxxxx model number and look up the part number. You do not want to buy a belt just by the size alone but must use one that is made for the machine application. The cheaper ones that you pick up in the local hardware store etc. like a 3Lxxx or 4Lxxx are made for low horsepower electric motors and will not last on your lawnmower.
How to Identify and Fix Common Gardening Problems ?
We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :
x 96-5/8 in. for 42 in. Deck Riding Mowers, Fits Cub Cadet, MTD, John Deere and more (R-75-813)
2x Deck Belt for 42″ Cut John Deere Saber Mowers L100 L102 14.542GS 1642HS LA105.
Gun Belt Length
The optimal length of the gun belt is determined by looking at your waist size plus how you carry. You typically want to wear a belt that measures four inches longer than your normal pant size. For example, if you normally wear size 38-inch pants, you may want a 42-inch belt.
There`s no standard size for a 42-inch-cut riding mower. Each model uses a different size belt. To give examples, some models use a drive belt that is ½ inch wide by 92 inches in length, while others use a belt ½ inch wide by 85 inches in length.
There`s no standard size for a 42-inch-cut riding mower. Each model uses a different size belt. To give examples, some models use a drive belt that is ½ inch wide by 92 inches in length, while others use a belt ½ inch wide by 85 inches in length.
Your belt size is two inches larger than your pant waist size.
Lay the belt on a clean, flat surface. Start the tape measure at the hole you use and measure to the end of the belt, where it meets the buckle. Belts are measured in inches and you should round to the nearest inch. If you measure 36 inches, you will want to purchase a size 36 belt.
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
Need a diagram for craftsman 44″ riding mower drive belt. Mine threw belt and cannot locate original manual.
ANSWER : If you can find the model number of your mower, you should be able to find your manual here. I hope this helps.http://www.searspartsdirect.com/partsdirect/index.action
Read Full Q/A … : 20 hp 42 in. Deck Lawn Tractor – CA Model
Need to replace drive belt.Never replaced. 42′ Craftsman riding lawn mower. How difficult is this. How do you access rear drive pully
ANSWER : Take a look at how the belt is installed. Then you will have to remove the mower deck and belt from the pulley on the engine. There is probably something by the engine pulley that you will have to remove so the belt will come off. It might be a shoulder bold or a rod with a bolt holding it on. Same with the rear pulley. Then you just have to put the belt on one pulley and watch your fingers so you don’t pinch them and turn the other pulley and the belt should go on. reinstall any bolts you removed and install the deck.
Read Full Q/A … : 20 hp 42 in. Deck Lawn Tractor – CA Model
What would cause my craftsman lt 1000 to chew up ground drive belt?
ANSWER : A bad pulley – bent- binding bearing-loose belt guides
Read Full Q/A … : 20 hp 42 in. Deck Lawn Tractor – CA Model
How to fit new belt – Craftsman 20 hp 42 in. Deck Lawn Tractor – CA Model
ANSWER : Ya gotta have model numbers. Go to searspartsdirect.com and enter your model number. Most models then have manuals available over on the right hand side of page. Most manuals have pictures or diagrams on bets.
Read Full Q/A … : 20 hp 42 in. Deck Lawn Tractor – CA Model
Drive belt popped off by limb i ran over need drive belt diagram
ANSWER : I’ve got a manual. Can I fax to you copy of diagram? Send your info to my fax no. 209-394-0868.
Read Full Q/A … : 20 hp 42 in. Deck Lawn Tractor – CA Model
I’m having trouble replaceing the motion drive belt on my LT1000 lawn tractor. The mowing deck is off, the old drive belt is off. I can’t get the belt around the transaxle pully. Any suggestions?
ANSWER : Often there is a keeper on the back of the pulley, and the belt must go inside the keeper. Get an inspection mirror up in there to look if necessary. Start by putting the belt on the transaxle pulley, then on the PTO pulley, then on the idler, last have someone sit on the mower and depress the clutch pedal while you put the belt over that pulley.
Read Full Q/A … : 20 hp 42 in. Deck Lawn Tractor – CA Model
Need routing guide for main drive belt
ANSWER : Hopefully this will help
Read Full Q/A … : 20 hp 42 in. Deck Lawn Tractor – CA Model
Craftsman riding mower loose belts need tighting
ANSWER : Http://www.disruptit.com/manuals/L0403195.pdf
Here ya go.
Read Full Q/A … : 20 hp 42 in. Deck Lawn Tractor – CA Model
