20″ 60cc Rancher Chain Saw 460
Experienced gardeners share their insights in answering this question :
Husqvarna Genuine Parts – Reliable Spare Parts for Homeowners
How to Identify and Fix Common Gardening Problems ?
We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :
Compatible with Husqvarna chainsaw models 455 Rancher and 460 Rancher, this genuine Husqvarna Rancher 20-inch chainsaw bar features 3/8-inch pitch, . 058-inch gauge, 72 drive links and a recommended 7/32-inch file size.
Chain Type: Semi Chisel. Pitch: . 3/8″
Oregon Chainsaw chain for Stihl Chainsaw 20″ Bar Length 72 Drive links 3/8 Standard 0.05 Gauge.
Husqvarna 460 Chainsaw 20″ 3/8″ Bar and Chain – OEM.
The letters on the screws represent High (H), Low (L) and Idle (T). The H screw regulates the Air/Fuel mix during high RPMs, while the L Screw does the same during low RPMs. The T screw regulates how much fuel is sent to the carburettor while idling until the throttle is pressed.
Husqvarna 460 Rancher 24-in 60.3-cc 2-cycle Gas Chainsaw.
File the teeth from the inside towards the outside. The easy way to remember the correct direction is that the tip of the file should always point away from the engine. Hold the file at a 90-degree angle to the flat sides of the guide bar. Move the file at a 30-degree angle to the straight line of the chain.
The Husqvarna HT-280-68 18-Inch replacement bar features 3/8-inch pitch and . 050 gauge and fits the following Husqvarna saws: 257, 261, 262XP,357XP, 359, 362XP, 455 Rancher, 460, 460 Rancher and 562XP.
Most chainsaws can operate up to three different bar sizes. Guide bars are measured in length, from the tip of the bar to the heel, and range in size from 14 to over 40 inches. Check the specifications in your model`s operator`s manual to see what size bars you can run on your saw.
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
What causes the chain on my 240E to jump off the chain bar often, the chain tenson is correct.
ANSWER : Is the bar bent?try and flip it over and see if it falls off the other side if you can see a bend
Read Full Q/A … : 20″ 60cc Rancher Chain Saw 460
My 290 isn’t oiling chain. I tried adjusting oil flow and still no oil?
ANSWER : You have to remove the bar and clean it out
Read Full Q/A … : 20″ 60cc Rancher Chain Saw 460
Oil is not lubing the chain on bar, what would be causing it?
When using the chainsaw, the chainsaw siezes, and makes the engine run sluggish. The bar and chain we not is not getting oil. The oil reservoir is fulled.
Hope this is not one of those ********, pay us first before we help us website situation.
ANSWER : Sounds like the ports on the bar are possibly clogged with debris or the oil lines going down to the bar are clogged. Check both of them to see if that might be the problem.
Read Full Q/A … : 20″ 60cc Rancher Chain Saw 460
On a husqavarna 362 xp special 71cc chainsaw very little oil is coming out to the chain i have removed the chain and bar and cleaned and still very little oil is making it to the chain what should i do ??
ANSWER : Check to see if there is an oil-volume adjustment screw located near the lower part of the chain where it goes into the cover, but mounted in the main case. It might be underneath the case in about the same location. Turn it CCW somewhat, if found, and check for oiling by holding the bar tip running at speed near some cardboard. If properly oiled, it will throw off a thin line of oil after several moments. If there is no adjustment, then you will have to investigate the oil pump, lines, and filter/valve in the oil tank. Make sure to clean the small oil passages in the drive end of the bar. Hope this helps!
Read Full Q/A … : 20″ 60cc Rancher Chain Saw 460
I have a Poulan 295. I needed to replace the chain. It is a 20″ chain. There is bar oil in the resevoir. The chain will not stay on the bar (it seems loose even when fully tightened). I replaced the bar and the chain still kicks off when I am cutting wood.
ANSWER : I did the same thing to my poulan pro 295 and had to order a screw tightener since the original only had the bar tightened from the bar itself. The chain brake cover has provisions for a traditional screw tightener so it was an easy fix, you didn’t say if you had put a screw tightener on yours.
Read Full Q/A … : 20″ 60cc Rancher Chain Saw 460
Chain saw chain is loose
ANSWER : Loosen the side cover nuts, then turn the adjuster CW to bring the chain up to the lower edge of the bar, then check to see if the chain will move fairly easily by hand. Tighten the clamp nuts and recheck tension. If chain seems to get loose quickly again, it may not be sharpened correctly causing heat to build in the chain. You should see no reflection of light from the cutting edges if filed correctly and the saw should require very little pressure for it to cut rapidly. Hope this helps!
Read Full Q/A … : 20″ 60cc Rancher Chain Saw 460
My 18 Inch chain saw will not keep oiling the Chain, I had it worked on and He said it was plugged. How do you unplug it with out taking it all apart. Is there a spot to blow air through. the Preacher..
ANSWER : Remove the chain bar and look just below the bolts holding it in place. You’ll see a small hole where the chain bar oil pump pushes out oil. Make sure this hole is clear then run the saw without the bar on.
Be CAREFUL of fingers!
You should see oil coming out of that hole. If not, you may need more serious work done with the saw (chain bar pump replacement).
Read Full Q/A … : 20″ 60cc Rancher Chain Saw 460
Bar chain oil leaking into case when not in use
ANSWER : If you store it somewhere other than a climate controlled building , the changes in temperature can cause the oil to expand out of the saw a little each time the temp. goes up.
try some absorbent cloth
Read Full Q/A … : 20″ 60cc Rancher Chain Saw 460
