Briggs & Stratton

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

A clogged carburetor is most commonly caused by leaving fuel in the pressure washer for a long period of time. Over time, some of the ingredients in the fuel may evaporate, leaving behind a thicker, stickier substance. This sticky fuel can clog up the carburetor and cause the engine to run stall.
One of the most common reasons a pressure washer won`t stay running is because the spark plug is dirty or damaged. To clean the spark plug, you will need to remove it from the engine and use a wire brush to remove any build-up on the electrode.
Water leaking from a loose connection can cause the unit to cycle on and off. Verify if the pressure hose has an O-ring at the connection. If missing, this will also cause the unit to cycle on and off. While the unit is running look for any water leaks that may cause the unit to turn back on.
Stale fuel that`s been sitting in a gas pressure washer may need to be cleaned out. If your gas-powered Generac, DeWalt, or Craftsman power washer won`t start, it could be because of old fuel. Fuel that`s been sitting in your gas pressure washer for 6 months or more can oxidize and become contaminated.
How Do I Tell If My Unloader Valve is Bad? In most occurrences, the first symptom of an unloader valve going bad is no pressure from the wand when the trigger is pressed. This happens when the unloader valve gets stuck open and does not allow water to enter the hose and trigger.
A clogged carburetor is most commonly caused by leaving fuel in the pressure washer for a long period of time. Over time, some of the ingredients in the fuel may evaporate, leaving behind a thicker, stickier substance. This sticky fuel can clog up the carburetor and cause the engine to run stall.
If a washer stops mid-cycle, it could be because the pump or the motor that runs it has failed. When this happens, it cannot remove the water efficiently, pump water in, and thus the sensors won`t allow it to move to the next cycle.
Some of the most common faults that will make your washer stop mid cycle include thermostat failure, problems filling up with water for the rinse cycle, or even pump problems that prevent your washer from draining. One thing that you can check yourself is the lid switch.
Machine Type: Gas pressure washers can typically run for about 30 minutes before they need a break. Electric models can usually go for an hour or more.
How Do I Tell If My Unloader Valve is Bad? In most occurrences, the first symptom of an unloader valve going bad is no pressure from the wand when the trigger is pressed. This happens when the unloader valve gets stuck open and does not allow water to enter the hose and trigger.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

Craftsman pressure washer 3100 2.8 has been sitting outside and can’t get it started
ANSWER : I would first start with fresh gas

Read Full Q/A … : Briggs & Stratton

After turning off power washer, it makes several creaking or groaning like noises. Never heard it , its a craftsman wash power washer, is there something wrong. Or is it getting too hot.
ANSWER : Bad pump

Read Full Q/A … : Briggs & Stratton

Oil type 2400psi
ANSWER : Any hosue holdcar motor oil will work

Read Full Q/A … : Briggs & Stratton

Wont stay running – Mtd 22" Yard Machine Push Mower
ANSWER : Under neath the carby is a single brass bolt, undo it

that one bolt is a multi jet, find four holes use a fine pin and carby cleaner ,hint one is at the top were the thread starts , one is in the inside center and two in the sides
put it back in and prim and start, hope it helps

Read Full Q/A … : Briggs & Stratton

How do i remove gas tank cover? – Craftsman 2700 PSI Briggs Stratton Powered Pressure Washer
ANSWER : Hey Chuck
Not sure of the model washer you have but most Briggs tank covers only have 2 bolts on top holding the cover to the tank. If the isnt it can you be more specific with a model number?

Read Full Q/A … : Briggs & Stratton

Craftsman mower with 6.75 B&S motor will start and run fine for about 3-4 minutes and then slowly chokes out. I cleaned the air filter and need to know what to check next. Thanks.
ANSWER : Hi there

though you have cleaned the filter it could still be not getting enough air you can start the machine without it and see if stays running do not do work with it just see if it runs sitting there if it does simple fix new filter however if it does the same it is a lack of fuel either fuel filter if has one if not it will be in the carburater these get gumed up by old gas in which in that case find a small engine repair shop to take care of this issue

thank you for the question hope i helped with the issue good luck and have a great day

Read Full Q/A … : Briggs & Stratton

Poulan pro chain wont stay running – Poulan Pro Chain Saw 46cc 20"
ANSWER : Keep “poulan” ha ha

Read Full Q/A … : Briggs & Stratton

Troy built power washer not pumping water only 2 years old
ANSWER : Replace pump or service valves or check inlet for obstruction

Read Full Q/A … : Briggs & Stratton