Garden
How to Identify and Fix Common Gardening Problems ?
We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :
A clogged carburetor is most commonly caused by leaving fuel in the lawn mower for a long period of time. Over time, some of the ingredients in the fuel may evaporate, leaving behind a thicker, stickier substance. This sticky fuel can clog up the carburetor and cause the engine to stall.
A Dirty Carburetor Can Cause a Lawnmower To Start Then Die
By far, the most common issue that causes a stalled motor is a dirty carburetor. The carburetor on your engine is the thing that draws in air and mixes it with the fuel. Contrary to what the movies might make you think, gasoline itself is not very flammable.
A dirty carburetor is the most common cause of a lawn mower that starts and then dies. Other possible causes include: Stale/Dirty Gas. Faulty Choke.
As the fuel level drops, a vacuum begins to form in the fuel tank because air can get in to fill the space the consumed fuel occupied. After about 10 or 15 minutes, the vacuum will become strong enough that fuel will stop flowing to the carburetor and the lawnmower will die.
If your lawn mower starts, runs briefly, then dies these are the four most common reasons that`s happening: Dirty carburetor / clogged carburetor bowl. Old gasoline that has gone bad. Dirty or defective spark plugs.
Being Overworked. One of the most common reasons that a lawn mower might stall while it is cutting grass is that it is being overworked. This is a mechanism that is intentionally incorporated into the mower to prevent the motor from being blown.
A full gas tank and oil reservoir are the essential first steps when checking why the lawn mower won`t stay running, but the problem could also be a dirty filter, clogged carburetor, improper fuel mixture, or a dirty spark plug.
The spark plugs are worn or damaged
If you find that your lawnmower keeps dying, or keeps stalling while cutting grass, then inspect the spark plugs. Look for signs of damage or wear. Something as simple as a cracked porcelain insulator can mean an electrode has been damaged or burned away.
The most common cause of a mower that runs for thirty minutes and then dies is a faulty armature. A faulty gas cap is the second most likely cause.
A full gas tank and oil reservoir are the essential first steps when checking why the lawn mower won`t stay running, but the problem could also be a dirty filter, clogged carburetor, improper fuel mixture, or a dirty spark plug.
A dirty air filter inhibits the flow of air into the carburetor. Clean or replace the air filter to stop the mower from sputtering to a halt. Too much air can also cause problems for the engine. A bad cap on the gas tank is the first place to look.
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
Need to add oil in my hydrostatic tranny – Craftsman 42 in. Deck 19.5hp Lawn Tractor
ANSWER : There a plug on top of transaxle.
Read Full Q/A … : Garden
Craftsman riding mower lt-1000 leaks gas – Craftsman 17.5 hp 42 in. Deck Lawn Tractor – CA Model
ANSWER : Need to fix that. it may be a fire hazard.
Read Full Q/A … : Garden
How do I get my carburator to get gas – Craftsman 42 in. Deck 19.5hp Lawn Tractor
ANSWER : Be sure the wire on bottom of carb, is plug in and switch turn on,
Read Full Q/A … : Garden
Trimmer will run on prime untill i try to pull throttle then stalls out
ANSWER : Hi mdnelson426…
Sounds like you have dirt/debris in your caburetor jets,fuel passages or a diaphgram that is becoming non-flexible. Check/Clean/Replace your Air Filter, a dirty air filter can make your engine run to rich with fuel.
Note: ALWAYS USE COMPRESSED AIR TO CLEAN YOUR JETS AND PASSAGES, VERY IMPORTANT.
Note:Before you disassemble the carburetor:Mark each piece with a awl, or some kind of instrument that will make an alignment scratch before you disassemble the carburetor into separate pieces.That way you will know which way it goes back together when you reassemble it.
Sometimes you can get by with priming the carburetor or by using starting fluid and letting it run a few times like that, and it will flush the gunk out of the jets,but most of the time you will need to rebuild the carburetor.Be sure to check your fuel tank for water and dirt/debris, if there is water/debris then you need to clean your tank.Check you fuel line condition after a while they will degrade and need replacment.
Check/Clean/Replace your fuel filter if you have one, normally they are located in the fuel tank of trimmers.When you remove your fuel lines from the carburetor be sure to make a drawing to how the lines are connected to the carburetor.Normally the big line will be the line the fuel filter is connected to inside of the tank.The smaller of the two lines is the return to the fuel tank from the carburetor after it is pumped thru the carburetor by the primer bulb.Make sure you are using fresh fuel…and oil mix if your using a two cycle trimmer with the oil to the right mixture and not too much oil as it can cause hard starting.If the trimmer is over a couple of years old, then I recommend that you buy and install a new carburetor repair kit,because the diaphragm will get hard and that will cause it to be hard to crank.The diaphgram may look good and flexible, but it can be deceiving and not act as a fuel pump as it should because it has become too hard and will cause hard starting,start and run and shut off, etc.
When you clean your carburetor, I recommend that you use a laquer thinner type cleaner to clean and dissolve the laquer build-up in the float and needle jet passages.Be sure to remove all plastic and rubber parts before using the laquer thinner because it can dissolve the plastic parts and render them unuseable.Be sure to use COMPRESSED AIR to blow out all the fuel and air passages.The higher air pressure is needed to blow some of the trash/debris from the fuel or air passages.Be careful when blowing out the passages, because there are sometimes small rubber type seats in the bottom of some of the passages.Keep in mind that the float (if you have one) for the carburetor must be level when you go to reassemble the carburetor or follow the instructions you get with the carburetor kit, or you could also ask the parts man that you get your kit from.When you clean your carburetor and remove the jet screws, you will first need to lightly seat the jet screws.But before you lightly seat the jet screws count the number of turns it takes to seat the jet screws from their original position.Be sure to mark the turns down on a piece of paper.That way when you put the jets back in, you know to lightly seat them first and then turn them back out to their original position before you started.Note:The little spring inside of the carburetor goes under the float arm.That is where your fuel inlet needle/float valve is located…on the arm at the end.Normally there is a small indetion in the carburetor base and a small protrusion on the underneath of the float arm where the spring will be in the right postion for installation.The spring will set in the indention and you will install the float arm with the needle/float valve and float rod into position over top of the spring,you will push down until it is in position and then you can tighten the screw that holds the float arm assembly in position.Once you have your carburetor cleaned/rebuilt that should solve your problem.Please take time to rate me
Sounds like you have dirt/debris in your caburetor jets,fuel passages or a diaphgram that is becoming non-flexible. Check/Clean/Replace your Air Filter, a dirty air filter can make your engine run to rich with fuel.
Note: ALWAYS USE COMPRESSED AIR TO CLEAN YOUR JETS AND PASSAGES, VERY IMPORTANT.
Note:Before you disassemble the carburetor:Mark each piece with a awl, or some kind of instrument that will make an alignment scratch before you disassemble the carburetor into separate pieces.That way you will know which way it goes back together when you reassemble it.
Sometimes you can get by with priming the carburetor or by using starting fluid and letting it run a few times like that, and it will flush the gunk out of the jets,but most of the time you will need to rebuild the carburetor.Be sure to check your fuel tank for water and dirt/debris, if there is water/debris then you need to clean your tank.Check you fuel line condition after a while they will degrade and need replacment.
Check/Clean/Replace your fuel filter if you have one, normally they are located in the fuel tank of trimmers.When you remove your fuel lines from the carburetor be sure to make a drawing to how the lines are connected to the carburetor.Normally the big line will be the line the fuel filter is connected to inside of the tank.The smaller of the two lines is the return to the fuel tank from the carburetor after it is pumped thru the carburetor by the primer bulb.Make sure you are using fresh fuel…and oil mix if your using a two cycle trimmer with the oil to the right mixture and not too much oil as it can cause hard starting.If the trimmer is over a couple of years old, then I recommend that you buy and install a new carburetor repair kit,because the diaphragm will get hard and that will cause it to be hard to crank.The diaphgram may look good and flexible, but it can be deceiving and not act as a fuel pump as it should because it has become too hard and will cause hard starting,start and run and shut off, etc.
When you clean your carburetor, I recommend that you use a laquer thinner type cleaner to clean and dissolve the laquer build-up in the float and needle jet passages.Be sure to remove all plastic and rubber parts before using the laquer thinner because it can dissolve the plastic parts and render them unuseable.Be sure to use COMPRESSED AIR to blow out all the fuel and air passages.The higher air pressure is needed to blow some of the trash/debris from the fuel or air passages.Be careful when blowing out the passages, because there are sometimes small rubber type seats in the bottom of some of the passages.Keep in mind that the float (if you have one) for the carburetor must be level when you go to reassemble the carburetor or follow the instructions you get with the carburetor kit, or you could also ask the parts man that you get your kit from.When you clean your carburetor and remove the jet screws, you will first need to lightly seat the jet screws.But before you lightly seat the jet screws count the number of turns it takes to seat the jet screws from their original position.Be sure to mark the turns down on a piece of paper.That way when you put the jets back in, you know to lightly seat them first and then turn them back out to their original position before you started.Note:The little spring inside of the carburetor goes under the float arm.That is where your fuel inlet needle/float valve is located…on the arm at the end.Normally there is a small indetion in the carburetor base and a small protrusion on the underneath of the float arm where the spring will be in the right postion for installation.The spring will set in the indention and you will install the float arm with the needle/float valve and float rod into position over top of the spring,you will push down until it is in position and then you can tighten the screw that holds the float arm assembly in position.Once you have your carburetor cleaned/rebuilt that should solve your problem.Please take time to rate me
Read Full Q/A … : Garden
My craftsman dys 4500 26hp 54 – Craftsman 26 hp 54 in. Deck Deluxe Yard Tractor – CA Model
ANSWER : Whats the problem?
Read Full Q/A … : Garden
I need a operating maual for a craftsman riding mower 28990
ANSWER : Sears Manage My Life has the Operator’s Manual: . Click on “Craftsman Lawn, Tractor” to get to the manual page.
Read Full Q/A … : Garden
How can I get the belts on? – Craftsman 42 in. Deck 19.5hp Lawn Tractor
ANSWER : Lots of sweat and foul words sometimes even a lot of blood . Water Filters Lawn Garden Appliance Parts
Read Full Q/A … : Garden
Craftsman DGS 6500 garden tractor won’t engage
ANSWER : Hi
There is a pin in the back by the hitch – make sure it is pushed in. If it is pushed in then check to see if there are any oil leaks under it.
There is a pin in the back by the hitch – make sure it is pushed in. If it is pushed in then check to see if there are any oil leaks under it.
Read Full Q/A … : Garden
