Garden

Experienced gardeners share their insights in answering this question :
Depending on the chainsaw, you will have an outer nut on the right hand side of the bar the chain

rides on, you have to loosen this nut, and on the left side against the body to the left of the bar

there is a screw clock wise to the right will tighten the chain, and counter clock wise will loosen

the chain. when you tighten the chain do not over tighten, never grab the chain on the bar with your

bare hands either use gloves or a rag, you want the chain to be able to move freely around the bar

but you do not want it to bind or come off the bar . once you have it adjusted make sure you lock

down the outer nut or nuts. make sure the chain is always oiled to prevent accidents. good luck!

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

Turning the adjusters clockwise will tighten the chain, and counterclockwise will loosen it. By turning the adjusters, you`re moving the whole wheel up and down the swingarm, so moving them gradually and equally on both sides of the bike is essential.
Chainsaw chains stretch during normal operation and begin to sag on a saw`s guide bar. If a chainsaw chain is allowed to become too loose, it can easily come off the bar during operation and create an unsafe situation for the user. Chainsaw chain tension should be checked and tightened often.
During a typical afternoon wood-cutting session that lasts 2 to 4 hours, you may need to tighten the chain two or three times. But, it`s quick and straightforward since you don`t need to disassemble the saw. Keep a scrench nearby for tightening.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

How do you tighten a chain on a worx wg307 – Worx Jaw Saw Wg307 – The Chainsaw Re-invented Jawsaw
ANSWER : When I took the saw screws out to clean the inside there was a black washer that fell out and I have no idea where it came from. cCan anyone awnser this question for me, please.

Read Full Q/A … : Garden

Cannot tighten the chain bar
ANSWER : Make sure the bar is positioned on the bar adjusting pin before you tighten cover. Adjust tension with bar adjusting screw, then tighten bar bolts.

Read Full Q/A … : Garden

Electric chain saw chain adjustment. How loose should it be?
ANSWER : The chain should not be sagging from bottom of bar.when you tighten the chain push the nose of saw up so that all of the slack is out of the chain.chain should snap back in the bar if you pull the chain up and let go.when i adjust a chain i push the saw forward to make the bar go up and stay there while i tighten the nuts.hope this helps, let me know

Read Full Q/A … : Garden

The chain popped off and I can’t get it to fit back on.
ANSWER : Losen the bar mounting nut, then losen the chain tension adjustment screw until the chain can be reinstalled, then tighten the tension screw until the chain just sags 1/8″ or so at the center of the bar then retighten the bar mounting nut.

Read Full Q/A … : Garden

How do I tighten my chain? its too loose and keeps falling off.
ANSWER : Mike’s answer might do it. My saw has a feature in the Chain Bar to turn right or left to move the Bar in or out. Loosen those same nut Mike wrote about, but now turn the Bar Feature (gear) to adjust, and then tighten the two nuts.

Read Full Q/A … : Garden

Chain keeps coming off – Remington Electric Chain Saw
ANSWER : Normally, a loose chain will enhance it’s ability to jump off when trimming small branches.When installing and/or adjusting a chain;1) install the chain, bar, and cover, and install the cover nut loosely2) support the ‘nose’ end of the bar with a block3) tighten the chain until it touches the bottom of the bar, and then tighen the adjuster 1/8 of a turn more. *this will make the chain just a LITTLE snug4) tighten the cover nut, and then by hand CAREFULLY rotate the chain. If you cannot rotate by hand, it is too tight. re-adjsut
** This proceedure must be used on ANY brand chain saw. Here is why. If the bar nose is not lifted upon adjustment, when cutting, the nose will move upward, the chain will have a ‘droop’ away from the bar and appear to have loosened while cutting. Any contact with a small branch will flip the chain off of the bar. If you re-adjust it improperly, the same senerio will occur the next cut.

Read Full Q/A … : Garden

Chain saw chain is loose
ANSWER : Loosen the side cover nuts, then turn the adjuster CW to bring the chain up to the lower edge of the bar, then check to see if the chain will move fairly easily by hand. Tighten the clamp nuts and recheck tension. If chain seems to get loose quickly again, it may not be sharpened correctly causing heat to build in the chain. You should see no reflection of light from the cutting edges if filed correctly and the saw should require very little pressure for it to cut rapidly. Hope this helps!

Read Full Q/A … : Garden

I can’t tighten the chain. I turn the wheel to tighten it, but the little catch that fits in the hole on the bar does not move. the wheel turns but the chain remains loose
ANSWER : If this is the tooless chain tentioner, i would suggest the small gear arrangment in the cover has stripped, many of the gears were only plastic, remove the screws holding the cover over the mechanism and check what has striped

Read Full Q/A … : Garden