T14560 T – 60″ Trailmower with 14 – 1/2 – Horsepower Briggs…

The cord tore off and can not repair. What should I do?
Experienced gardeners share their insights in answering this question :
What do you have and what is wrong with it

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

Mower Won`t Start

First, check your gas levels. This might seem obvious, but many times, a mower that won`t start is simply out of fuel. If gas isn`t the issue, check your mower`s spark plugs and ensure they are connected, tightened, and cleaned. Your mower might struggle to turn on if the air filter is dirty.

Loose, Dirty or Disconnected Spark Plug in Your Lawn Mower: Check it out, clean off debris, re-connect and tighten. Dirty Air Filter: Clean or replace. Fuel Not Reaching the Engine: Tap the side of the carburetor to help the flow of gas. If this doesn`t work, you might need a new fuel filter.
Possible cause 1: In some models, when you tip the mower, fuel can leak into the carbon in the cap, which restricts the venting of the fuel system. This can cause the engine not to start, or only run for a few minutes, then quit. POSSIBLE SOLUTION: Leave the cap to dry out or replace it with a new lawn mower cap.
Why Is Your Lawn Mower Pull Cord Hard To Pull? Your lawn mower pull cord hard to pull is because of the way you pull the cord, the area where your mower is located when you are trying to start it, because it has a blade obstruction, or because of a starter mechanism-related issue.
Swisher Sweets Sweet Original Foil Wrapped cigarillos (4 7/8″ x 28) are the same mellow-smoking, smooth cigars that put the company on the map, only now it comes in the foil wrappers to improve freshness. Great taste, quality and affordability is a winning combo and is the reason Swisher Sweets is on top of the game.
Why Is Your Lawn Mower Pull Cord Hard To Pull? Your lawn mower pull cord hard to pull is because of the way you pull the cord, the area where your mower is located when you are trying to start it, because it has a blade obstruction, or because of a starter mechanism-related issue.
The reasons why mower is not moving forward or reverse is that the battery is dead, or due to clogged fuel line. Additionally, malfunctioning transmission, or a broken drive belt, also a faulty spark plug, even when friction wheel isn`t in contact with the friction plate, or damaged Tires.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

What to do when craftsman mower pull cord won’t recoil?
ANSWER : Sounds like the spring inside the recoil has either broken or let go so it won’t recoil. If you are lucky it could be the wheel that the cord goes on is seized or stuck. You can take the recoil off most mowers by taking out two or three screws and lifting it off the engine. They can be repaired but it takes time having to be careful the spring won’t spin and hurt you. I have even taken a recoil off another engine and if the holes for the little screws don’t line up just drill little holes beside the old ones and reinstall the little screws.
I even used a 18 volt cordless drill to crank the engine using the bolt on the fly wheel and the right size socket. Leaving the recoil off You have an electric start that way.

I have a toro self propelled 6 hp lawnmower battery and pull start it wont start with battery but will with pull cord
ANSWER : Try to start it using jumper cables to boost it from another battery. If it starts, your battery needs replacing.

I can’t start it because the pull cord is stuck and it happened after I installed a new blade.
ANSWER : If the recoil assembly has three screws holding it in place, remove them, lift the recoil assembly off and see if it works off the mower. If it does, reassemble.
Gary

Troy Bilt Lawn Mower pull Cord broken
ANSWER : There should be four bolts holding the cover on that houses the pull cord assembly take the bolts out look inside you should see the rest of the broken cord at the other end there is a spool that the cord rolls up in to pull the cord until it stops the other end of the cord is a not in the cord pull on the knot the broken peice should come out turn the spool 2 times in the direction that is against the pressre while holding the spool in place feed the new cord in through the whole that you pulled the broken cord out of then tie the cord in a knot wind the rest of the cord up then feed the other end of the cord through the new pull handle tie the cord in a knot put the housing back on

How do I replace broken pull start cord? – RTO Toro Lawn Boy 21in Insight Series Steel Deck Mower
ANSWER : There are screws holding the top of the mower on, you should be able to remove those and lift them to get access to the cord. From there it is easy. just put new cord back the opposite of the way you removed it, making sure that you get it wrapped the correct direction. you can get a cord anywhere they sell mowers.

Pull cord is difficult to pull after third pull becomes stuck but will turn if pull hard repeats every three to four pulls.
ANSWER : No response to clarification request.

Just installed a new pull cord…the cord does not retract. How do I fix the problem?
ANSWER : The best way i found is to twist counter clock wise a dozen turns,hold the spool with vise grips,feed the roop through all holes you need to go through, into the reel knot, i burn the knot, keeps it from slipping out,then slowly let the spring bring the slak in when i release the vise grips!

10 year old Toro 2017 lawnmower, suddenly stopped while cutting grass. Oil quite low. Cannot pull cord more l than few inches.
ANSWER : When you pull the cord does it hit a hard stop and not go any further or does it get really difficult?