Garden

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

If your washer won`t start, the buttons won`t work, or the control knob won`t select a different cycle, you probably have Child Lock turned on. If your Child Lock icon is lit or flashing, this confirms it. Turning Child Lock off will usually take care of your problem.
Unplug the washer for 60 seconds, and then try again

Resetting the washer will reboot the washer which can help fix certain problems, such as unresponsive buttons.

Make sure you are touching buttons correctly.

Some microwaves have capacitive touch panels. On these microwaves, make sure to touch the button with a bare finger. The button may not respond if there is not enough area of contact. Buttons should not require excessive force to press.

A: It takes about five to ten minutes to reset your Samsung microwave. You need to unplug the power cord for at least five minutes and then plug it back in. This will allow the microwave`s capacitor to discharge and reset its memory.
Reset your washing machine

There really isn`t a way to reset the washing machine. What you can do instead is power cycle it: Unplug it (or turn off power at the circuit breaker), wait some time for the electrical charge to clear out of the washer (usually 1 to 5 minutes at most), and then power it up again.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

Control panel reads 000, then 023, then 030 and goes back and forth. I can not change anything. Buttons do not work.
ANSWER :

Read Full Q/A … : Garden

Control panel on hot tub is flashing ECN – Balboa Instruments Duplex Digital Panel 2 Pump
ANSWER : The hot tub is in ‘Economy’ mode.

If you have a ‘mode’ button, press it until ‘STD’ shows. This will put the system back into the Standard mode.

If you don’t have a ‘mode’ button drop me an email with a picture of your keypad and I’ll try to advise you on what to press. [email protected]

Regards,
Ian.
http://hottub.synthasite.com

Read Full Q/A … : Garden

Upper control panel flickers and will not allow me to control temo
ANSWER : How old is spa?
if new then circuit board maybe set on a mode setting that is used when being tested in the factory, locate dipswitch block on circuit board and move dip switch for MODE, should have a layout of dip switches on reverse of lid to control box
if older then you may need a new control panel (top side)

Adam Miller, Canadian Spa Company, UK

Read Full Q/A … : Garden

I have a catalina spa with a balboa ct 205 control box and ozonator, it keeps tripping on start up , fresh water, clean filters,all jets open, it has been off for 2 mths and has been very cold,i have isolated all controls,blowers works fine,pump 2 works fine(twin speed)lights work ozonator works,but when i plug in pump 1 heater it trips,,,, in about 15 seconds display shows flo flashing,,,,i have bleed air and primed and turned pumps manually ,,,pump 1 heater turns for a few seconds prior to tripping,,,,,,,,,,,, is there a reset button i cannot see,,,,please help
ANSWER :

Read Full Q/A … : Garden

Need the pto to work on a 6300 john deere tractor we have changed the fuses and changed the sencer on the back can you help
ANSWER : If you have tried a new sensor and a new switch the the next step is to replace the pto solenoid valve.If that proves fruitless then the b.c.u.needs to be replaced or bypassed.The solenoid valve will cure your problem 90% of the time.If that does not work,let me know,i can tell you how to by-pass the b.c.u..

Read Full Q/A … : Garden

I have a balboa 8 man spa. We shut it off to drain and clean. When we were done it would not turn back on. Tub was working fine, but now it keeps tripping the gfi. After some trouble shooting. I got it to turn on but had to disconnect one of the 220 volt copper terminals on the heater. The tub powered up and all the jets worked. Am I right to thinks that the heater needs replaced? if so how do they come apart. Where can I get instruction on the heater removal.
ANSWER : YES it is the heater that is at fault.
you have 2 white water pipes that attach to heater that will need to be unscrewed (best to do with spa empty) and it depends on what control system you as to advise on heater removal. some heaters have pressure switches and others have 2x sensors or they may have both. also your heater will be held into place by brackets that are normally 8mm

Adam Mill, Canadian Spa Company, UK

Read Full Q/A … : Garden

I have a catalina spa with BALBOA CONTROL PANEL
ANSWER : Where are you from?

If you live in the UK give me a call/email as I have worked on lots of Catalina Spas over the years.
http://hottub.synthasite.com

Regards,
Ian.

Read Full Q/A … : Garden

Ford 7600 hydraulic pump leaking at test port i changed pump seal and leak came back! back after working with disc bine!
ANSWER : Check for scarring and chips that can tear the

Read Full Q/A … : Garden