sears 18″ Chain Saw Chain ( Model 35084 )

Experienced gardeners share their insights in answering this question :
Make sure the chain has not been damaged from past slipping by removing it from the machine and laying the chain out in a large circle on a flat surface. No part of the chain should be standing free of the surface–replace the chain if it does. The chain should be adjusted so that the chain just comes up to the lower bar edge, but not so tight that the chain cannot be turned by hand. Make sure the teeth are quite sharp for maximum cutting effect and minimum heat. Check the chain lubrication by running the bar tip at speed for a moment or two near some cardboard–it should throw off a thin line of oil. Don’t continue to run the saw if the chain starts to droop from the bar. If it is quite hot, allow it to cool which should re-tighten the chain. Hope this helps!

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

If your chainsaw still starts and then stops working, check the air filter. Clean or replace the air filter if it is dirty or damaged. Another reason that your chainsaw starts and then stops working could be that the spark arrestor is dirty or clogged. If this is the case, clean it with a wire brush.
Correcting the problem requires adjusting the idle screw – usually marked “I” – on the carburetor. The idle screw usually is near or behind the air filter. Adjust the screw to restrict fuel delivery by turning it clockwise with a screwdriver until the chain stops turning.
To determine whether the chainsaw chain is stretched, pull the chain away from the chainsaw`s guide bar to see if there`s space between the two. If there`s space between the chain and the chainsaw`s guide bar, then the chainsaw chain is stretched.
STIHL 63 PM3-56 chainsaw chain made in Switzerland with high quality steel. This chain fits Homelite, Poulan, Echo, Craftsman, Remington and others with the same specs.
Oregon 16 in. Chainsaw Bar & S56 Chain, Fits Craftsman, Echo, Poulan, Homelite, Makita, Husqvarna, Ryobi and more (27857) | Oregon Products.
The carburetor might be clogged. A clogged carburetor is often caused by leaving fuel in the chainsaw for a long period of time. Over time, some of the ingredients in the fuel may evaporate, leaving behind a thicker, stickier substance. This sticky fuel can clog up the carburetor and cause the chainsaw engine to stall.
Always cut on the compression side first! The area on the outside of the bend will pull apart when cut. This is the tension side. If you decide to cut this side only, the tree will split apart before the cut can be completed.
The rule of the thumb says that the exact tightness of a chain will only let you move for about half an inch. Now, if the chain is too loose, then you need to tighten it. If you cannot even move the chain, then it is too tight, and it needs to be loosened.
A chainsaw chain can be sharpened up to 10 times, sometimes more, before the entire chain needs replacing. It`s mostly dependent on two things; the amount of wear your chain incurs and the amount of metal removed every time you sharpen. Different materials can have a harder impact on the chainsaw chain.
A chainsaw blade typically runs in a clockwise direction. Clockwise. The chain travels around the bar in a groove and travels away from the motor over the top of the bar, then returns under the bar back to where the clutch drives the notches in the chain.
Correcting the problem requires adjusting the idle screw – usually marked “I” – on the carburetor. The idle screw usually is near or behind the air filter. Adjust the screw to restrict fuel delivery by turning it clockwise with a screwdriver until the chain stops turning.
Generally speaking, the chain should be a little loose on the chain saw guide bar, but not loose enough that the drive links come out of the bar nose. The bar links should feel like they are raising up, but not actually come out of the guide bar.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

Chain keeps slipping off when in use. – Craftsman sears 18" Chain Saw Chain ( Model 35084 )
ANSWER : Make sure the chain has not been damaged from past slipping by removing it from the machine and laying the chain out in a large circle on a flat surface. No part of the chain should be standing free of the surface–replace the chain if it does. The chain should be adjusted so that the chain just comes up to the lower bar edge, but not so tight that the chain cannot be turned by hand. Make sure the teeth are quite sharp for maximum cutting effect and minimum heat. Check the chain lubrication by running the bar tip at speed for a moment or two near some cardboard–it should throw off a thin line of oil. Don’t continue to run the saw if the chain starts to droop from the bar. If it is quite hot, allow it to cool which should re-tighten the chain. Hope this helps!

Chain keeps slipping off saw – Craftsman sears 18" Chain Saw Chain ( Model 35084 )
ANSWER : Remove the bar and chain. Lay the chain out on a bench or table and examine for sideways bent/broken links, badly damaged cutting teeth, or damaged drive teeth. Inspect the bar chain-groove all the way around for any damage. Make sure the tip sprocket turns freely and is not damaged. Check the sprocket on the clutch drum for hooked teeth or other damage. Clean the small oil passages that feed oil out to the chain groove in the drive end of the bar. Start the engine and check the engine side port where the bar fits to–it should ooze out oil from the small port there. If everything checks ok, re-assemble the bar and chain leaving the cover fasteners finger tight. Adjust the chain until it pulls up to the bar, but not so tight that you can’t turn turn it by hand. Tighten the bar fasteners and re-check the chain tension. Start the engine and hold the bar tip near some cardboard–it should throw off a thin line of oil after several moments of running at speed. Hope this helps!

What does a spark plug gap at – Craftsman sears 18" Chain Saw Chain ( Model 35084 )
ANSWER : Hi, your spark plug gap should be the thickness of a hacksaw blade. use a hacksaw blade. sheers

Chain keeps falling off – Poulan 18" Chain Saw Replbar (small Saws)
ANSWER : Your chain is too loose. If you’re using an old chain, you might need to have a link taken out of it. You can find replacement chains for your saw at Hyperparts.com. Use the application lookup link at the top of the page with your model # to make sure you order the right chain.

Chain saw has no spark – Craftsman sears 18" Chain Saw Chain ( Model 35084 )
ANSWER : If it has no spark there are only a few that will cause this, firstly dissconnect the wire from the ignition switch, try again for a spark, if no spark, remove the starter cover, now remove the cut out wire from the ignition unit terminal, try again for spark, if no spark, the ignition unit is bad and will require replacment.

Saw will not start. – Craftsman sears 18" Chain Saw Chain ( Model 35084 )
ANSWER : Check for spark by removing the plug, connect the plug wire, and lay the base on engine metal. Pull the starter through several times which should result in blue, snappy sparks. If weak or nothing, try a fresh plug (gapped 0.020″). If still nothing or weak, remove the left side cover to expose the flywheel and ignition module. Turn the flywheel til the magnets are under the module poles. Insert a thin business card into the pole gaps, loosen the module screws, and allow the module to contact the magnets. Tighten the screws and turn the flywheel somewhat to remove the card. Turn the flywheel one full turn to make sure the gaps don’t close up any further. Remove the ignition switch wire from the module body, then try for spark again. If ok, reconnect the ignition switch wire and try for spark again. If now get nothing, check the switch/wire for a grounding short. If you still get nothing after the above test, replace the module using the above procedure. If the first test produced good spark, pour a little fuel mix into the hole and try for start, If you get several pops, you have a fuel delivery problem–check the fuel filter, air cleaner, and muffler for plugging. Check the fuel lines for decay or other damage. Make sure the carburetor is tight to the engine. Make sure to have fresh fuel mix in the tank. Hope some of this helps!

The chain keeps coming off and we just got it today.
ANSWER : Sounds like you do not have the chain tight enough. Read the book if it came with one. Good luck

Chain keeps coming off – Poulan Wild Thing 2375 18" Gas Chain Saw 2.5 Cuin
ANSWER : Open the chain guard.Once there look for a bolt that hold the chain plate.The chain plate has a large groove and the bolt.djust the chain by plull to the front until the chain is tight,but not too much,just test by hand if is move freely but tight.Reverse the procedure.If you need more help come back.Post / thumbs / testimonial are welcome!