Garden

There are no bolts to remove
Experienced gardeners share their insights in answering this question :
Most push mowers have 3 bolts around the side of the eng.

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

Why Is Your Lawn Mower Pull Cord Hard To Pull? Your lawn mower pull cord hard to pull is because of the way you pull the cord, the area where your mower is located when you are trying to start it, because it has a blade obstruction, or because of a starter mechanism-related issue.
Unfortunately, you also know the struggles that come with it. Your bathroom pull cord keeps breaking for 1 of 3 reasons. Either it`s had too much heavy-handed use, it was cheaply made, or you`ve got a loose wire somewhere.
Raises alerts in areas where personal triggers are unlikely to be worn. The emergency Pull Cord can be strategically placed around the home, in order to provide a user with a convenient means of summoning help in an emergency.
If the starter rope won`t budge when you try to pull it, the engine may be locked up or the recoil starter may have failed. If you tipped the pressure washer on its side recently, oil may have filled the cylinder, preventing the engine from spinning.
cord. Pulling the cord can damage it and may lead to. fire or electric shock.
Pull the plastic housing of the electric plug to take it out of the wall socket; never pull on the cord. Do not overload electric outlets with too many items plugged in at once.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

Troy Bilt Lawn Mower pull Cord broken
ANSWER : There should be four bolts holding the cover on that houses the pull cord assembly take the bolts out look inside you should see the rest of the broken cord at the other end there is a spool that the cord rolls up in to pull the cord until it stops the other end of the cord is a not in the cord pull on the knot the broken peice should come out turn the spool 2 times in the direction that is against the pressre while holding the spool in place feed the new cord in through the whole that you pulled the broken cord out of then tie the cord in a knot wind the rest of the cord up then feed the other end of the cord through the new pull handle tie the cord in a knot put the housing back on

Read Full Q/A … : Garden

Pull cord is difficult to pull after third pull becomes stuck but will turn if pull hard repeats every three to four pulls.
ANSWER : No response to clarification request.

Read Full Q/A … : Garden

Trying to replace the pull cord , can’t get last housing off to get to coile up old cord , the shaft has a nut on the end that the auger screws into but i cannot get that piece off as there is no where to put a wrench to stop the turning of the engine shaft so i can torque the nut in the other direction to get it off , what do i do to get this pull cord replaced?
ANSWER : Use an impact wrench it will hit the nut so fast it will loosen it befroe the engine car turn over

Read Full Q/A … : Garden

The pull cord will not recoil. what do i do? the spring behind the cord was just assembled and went to pull it and it wont recoil the pull cord.
ANSWER : It needs a pre-tension. At about 1 minute and 22 seconds it is explained clearly here:
SmallEng.com

Good Luck
Lou

Read Full Q/A … : Garden

Starter cord pulled out of the housing, it
ANSWER : If it’s new take it back should have a one year warrenty on it if yo can’t get it done for free get back to me so I can help you you may have a damaged windind head.

Read Full Q/A … : Garden

Broken pullcord the pull cord on my cub cadet push mowersnaped and broken and we put it back in and know it wont wind back in
ANSWER : Yeah I got the same problem. My pull cord broke in the first season. On my own once the plastic cover is removed, 4 phillips screws, the cord housing is secured by 3 10mm nuts. Remove them and lift out the housing. On my own unit the spring had also slipped out of the mount on the shaft securing the assembly (another 10mm socket nut will loosen that) and I had to resecure that first, then wind it up before making the knot.. I used a Briggs and Stratton cord from another (truly dead) mower and have had no problems since then.

Read Full Q/A … : Garden

Broken pull cord
ANSWER : You have to take four allen screw out of the plastic that holds the engine on. There is also one by the spark plug that needs to come out. Once the engine is loose, you have to unplug one wire and unscrew the other. Then the engine should come off. Then loosen the two allen screws holding the pulley in and it will come out.

Read Full Q/A … : Garden

Weed eater is locked up. can not pull cord at all.
ANSWER : Try taking the cover off around the pull if you can. Likely the cord is not free to spin, or there is a rub on the fly wheel stopping it from moving.

Read Full Q/A … : Garden