30 Cubic Centimeter Curved Shaft Gas Trimmer
Sounds simple, but I have a Ryobi strimmer with 2 heads – one with individual plastic cutting strips which are inserted into holes either side of the head. There is an alternative bump type head, supplied with the machine, which I would now prefer to use. However, try as I might, the existing head will not come away from the shaft, There is a central nut which has been removed but the whole assembly is still well attached to the shaft, and there is no visible means of removal. Anybody out there who could kindly let me know the next move?
Many Thanks // AL
How to Identify and Fix Common Gardening Problems ?
We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :
Worn clutch – Since the string trimmer clutch engages with one or more drive shafts attached to the trimmer head to rotate the head when the throttle trigger is depressed, a worn-out clutch may prevent the trimmer head from spinning. A new clutch assembly is relatively inexpensive and easy to install.
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
Where can i buy on line a Ryobi Puk head – Ryobi Expand-It 2 Cycle 26cc Trimmer Power Head
ANSWER : Clency try Central Spares
Read Full Q/A … : 30 Cubic Centimeter Curved Shaft Gas Trimmer
Ryobi strimmer petrol strimmer stalls on rev up can you solve this problem
ANSWER : I can not take the cover off to put the line back in
Read Full Q/A … : 30 Cubic Centimeter Curved Shaft Gas Trimmer
It wont start,I replaced the spark plug
ANSWER : Joe try putting some fuel in where the spark plug goes. If it still doesn’t fire then proceed to eliminate things. Firstly the air filter will need cleaning then the spark coil. If it still don’t fire check the switch is ok. Sometimes the switch breaks a circuit and helps with the running of it.
Read Full Q/A … : 30 Cubic Centimeter Curved Shaft Gas Trimmer
Strimmer wont start plug very dry when i remove it?
ANSWER : Sounds like the gas is not getting to the cylinder—remove carb and disassemble–make sure all jets are clear and the float valve moves freely.
Read Full Q/A … : 30 Cubic Centimeter Curved Shaft Gas Trimmer
Can not get spool head apart to change line, tried pump pliers, pipe wrench, won’t unscrew!!
ANSWER : If you are sure that it screws on it may be a reverse threaded unit..
Read Full Q/A … : 30 Cubic Centimeter Curved Shaft Gas Trimmer
Ryobi cs 30 why does the trim head turn on its own after started when I haven’t touched the throttle !!
ANSWER : Start with adjusting the carb low and high out 1 full turn, then adjust the idle.
Read Full Q/A … : 30 Cubic Centimeter Curved Shaft Gas Trimmer
How do you fix a jammed trigger on the Ryobi 10 Amp Electric Power head
ANSWER : Not really a fix but it worked for me. I opened up the case. Their is a little black box with a red button that must be depressed. Pulling up on the trigger pushes the button. Their is what i call a counter press above the trigger. By pressing it, it makes room for the trigger to slide up and press the red button. There isn’t much you can do improve this process. But i took the two springs off the trigger and depressed them trying to shorten them thus reducing the force needed to press. The counter press in spring load. I carefully stretch it by pulling on the end directly above the trigger(not against the frame). This took some pressure off the counter press. I finally took a small file and carefully filed down the edge of the counter press where the trigger presses against. This makes it slide upward easier even if the counter press isn’t pressed down fully when you squeeze it. The trick is pressing the counter press first, but doing these things has made my trigger a lot smoother. It use to be a hard press to activate, but now it is 10 times better than it use to be. Good Luck!!
Read Full Q/A … : 30 Cubic Centimeter Curved Shaft Gas Trimmer
No spark on plug when activated against cyl head .this tool is brand new and only ran for 5 mins then wouldnt start
ANSWER : If you want to check for a loose wire on the on/off switch or a problem with the spark plug wire contact on the plug, but personally if this tool is new I would return it and get a new tool without having to fix this one. Also I would try another spark plug before considering taking back. Sometimes plugs go bad
Read Full Q/A … : 30 Cubic Centimeter Curved Shaft Gas Trimmer
