Chain Saw 20″ Bar
I have 18″husqvarna chain saw.i took it to the shop to have it repair,it started one time and stop.could you tell me who to repair it.
Experienced gardeners share their insights in answering this question :
What shop did you take it to.if you took it back to where you bought it from it could be anywhere.make sure the saw has comperssion.easyist way to tell if you have good compression you need to take the muffler off and look to see if the piston is scored.Call husqvarna hot line and they will give you the nearest husqvarna dealer to repair it correctly.
How to Identify and Fix Common Gardening Problems ?
We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :
If your electric or gas saw`s chain won`t turn around the bar, chances are that the chain brake is stuck. On some saws, resetting the chain brake is as simple as pushing in on the side cover of the saw`s body with one hand, and pushing the chain brake forward while grabbing the top handle with the other.
If your STIHL chainsaw is going to have a problem, it`s likely to be with a worn carburetor, bad spark plugs, loose fuel hoses, or clogged fuel lines. You should also inspect the fuel intake system and ensure that there are no compression issues.
With the choke in the “off” position, pull the engine`s crank cord through again. The engine should start in 1 to 3 pulls. Try it first without using the throttle control—unless recommended by the manufacturer.
When engaged, the chain brake stops the chain from rotating around the saw`s guide bar. When using a chainsaw, you should always start it with the chain brake engaged so the chain does not move.
Many people wonder if a flooded chainsaw will fix itself? The answer is yes, but not always. By letting the chainsaw sit for about 20 minutes it will allow some of the fuel inside the engine to evaporate.
One tell-tale sign that a chainsaw has flooded is the smell of fresh petrol near the muffler. To ascertain whether this is indeed the problem, simply disassemble the part, pull the starter cord as if you were switching on the engine, then dry it, reassemble it and try switching it on again.
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
Toro clear won't start – Toro Power Clear 621 R
ANSWER : Bad gas , plug ,air filter , no spark ck all need all 3 to start
Read Full Q/A … : Chain Saw 20″ Bar
Does not run, will start with starting fluid – Mantis 2-Cycle Tiller
ANSWER : You should never use starting fluid on this model.
Add a couple of ounces of 100% acetone (available at Walmart) to some fresh fuel. Attempt to start for several pulls. Let sit for several minutes and repeat until it sounds like it wants to run.
Then watch this video and do it:
http://www.alamia.us/mantis_parts_s/148.htm
Read Full Q/A … : Chain Saw 20″ Bar
Snow blower wont start
ANSWER : Clean the fuel out and the carb , make sure you are getting spark close the choke to start then shut if off or it will foul the plug
Read Full Q/A … : Chain Saw 20″ Bar
Strimmer wont start plug very dry when i remove it?
ANSWER : Sounds like the gas is not getting to the cylinder—remove carb and disassemble–make sure all jets are clear and the float valve moves freely.
Read Full Q/A … : Chain Saw 20″ Bar
Tines continue to work with out touching safety or throttle. they engage as soon as I start the engine.
ANSWER : Remove H (high) L (low) plastic caps to allow you to further adjust the flow and you will be going. H (red) further out about 11 threads exposed and L (low) about 8 exposed; adjusting the low side will stop the tines, but remove tines before making any adjustments, thanks
Read Full Q/A … : Chain Saw 20″ Bar
Mower won’t start. Toro mower..engine won’t turn over. Cleaned sparkplug…checked air filter..weather cool. Followed instructions for cold engine…prime witrh three pushes of the bulb..wnon’t even hint at a start..
ANSWER : Something everyone over looks is oil. Did you check the oil? You seemed to mention everything else but. If you have a low oil switch with low oil it will not start
Read Full Q/A … : Chain Saw 20″ Bar
Cannot get the saw started – Husqvarna 450 e-series 18" Chain Saw
ANSWER : Check for spark check fuel filter carb kit if sitting for while new plug
Read Full Q/A … : Chain Saw 20″ Bar
<!– from fixya rte –>Rj19lm plug gap for a 195cc 4cyl lawnboy – Lawn-Boy lawnboy" Mower Blade 21"
ANSWER : As a starting point in my shop i always use 0.30 in. For all my mowers
Read Full Q/A … : Chain Saw 20″ Bar
