.
Poulan

Experienced gardeners share their insights in answering this question :
What end was pulled off.The end to the fuel tank goes into a small hole.The other end goes to carb. but sometimes it is difficult to see.Its easiest to take out the screws holding the carb and lift it enough to find the fitting.

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

You can find Poulan Pro products both in-store and online at home improvement retailers, hardware stores, and mass merchants all over North America. We are here to help you tackle… ANY YARD.
Most vehicles have rubber fuel hoses connecting the fuel pipes on the chassis to the fuel pump or carburetor on the engine. Rubber hoses are flexible and can be cut to length as required, but they have a tendency to perish over time and can rub through if not properly secured.
Poulan is a brand name of the Swedish manufacturer Husqvarna AB.
Husqvarna definitely owns Poulan.
Who Manufactures Poulan Chainsaws? Husqvarna Corporation, a Swedish organization, is currently manufacturing Poulan chainsaws. It has several production facilities across North America and is headquartered in Charlotte, North Carolina, USA.
A: Our units run on 87 octane regular unleaded gasoline. You can use gasoline which is blended with a maximum 10% alcohol. Never use E85 or diesel fuels. Remember to use fresh gasoline and to mix it with the recommended 2-cycle oil.
Insert a small flat-head screwdriver into the idle speed screw and turn it clockwise to increase the engine speed if it idles too slowly. As soon as the chain starts to move, turn the screw counterclockwise until the engine idles without dying and the chain stops moving for the correct idle speed.
The letters on the screws represent High (H), Low (L) and Idle (T). The H screw regulates the Air/Fuel mix during high RPMs, while the L Screw does the same during low RPMs. The T screw regulates how much fuel is sent to the carburettor while idling until the throttle is pressed.
They are typically labeled L (low speed jet), H (high speed jet), and I (idler jet).
The fuel line typically consists of rigid metal pipes, with flexible rubber or plastic hoses running from the pipes to the tank and the fuel pump , and from the pump to the carburettor .

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

Replaceing fuel line in polan 3300 chain saw – Poulan Pro 42CC 2 Cycle Chainsaw, 18"
ANSWER : Hi owjbhend…
Use a piece of wire and insert it into the fuel line, then bend a hook in the end and hook it over the end of the fuel line…lubricate the fuel line with some vaseoline very lightly…about the first one inch of the fuel line and then use your fingers to start the fuel line into the tank, once you have the fuel line in the tank give enough to hook the fuel filter to and so it can be dropped back into the tank.
Below is a drawing of how to route the fuel lines.
Please take time to rate me thumbs up
Please take time to rate me thumbs up

Read Full Q/A … : Poulan

Poulan te 450 cxl fuel lines need routed correctly two line both in tank one to fuel filter other line?
ANSWER : Other line is just left open like to send gas back from the carb.

Read Full Q/A … : Poulan

The fuel lines have rotted out of the edger gas tank. How do I fix or do I need to replace entire tank with new fuel lines?Since there are no male fuel line connections exiting the fuel tank and just two holes where the lines were, I guess I need to replace the entire tank and get a new one with lines already attached. Thanks.
ANSWER : No you can buy replacement fuel line but you must reconnect the filter in the tank that line goes to the bottom of the carby then out the top of the carby to the inlet on the primer then out of the primer and back to the tank.

Read Full Q/A … : Poulan

I need to replace to fuel lines on a Craftman 32cc trimmer. The old ones cracked apart. 2 of the lines look like 1/8″ OD one line looks like 3/32″ OD. Larger line looks like it hooks to filter, Smaller line to a fitting in the gas tank. I am assuming the smaller line ges to the primer inlet. My question is the lines penetrate the bottom of the gas tank. How do they seal. How do I install the filter and the fitting. I am assuming to thread the new lines in from the bottom of the tank and pull through the gas cap hole. Then I attach filter or fitting and pull back through. So do I pull the line so as to create a seal from the swell caused by the fitting/filter?
ANSWER : Depending on the brand of line you use, Tygon line is self sealing but seems to shrink faster then factory supplied because of the ethanol in the gas. The stone gas filter is designed to fall to the lowest part of the tank, not stop the line from falling out.

Read Full Q/A … : Poulan

Have a craftsman 16″ chain saw 358.360260. Could not initially get it started after it had sat for a couple years with fuel stabilizer in it. When I went to use it the fuel had all evaporated and the fuel pick line was rotted. I replaced that with some difficulty but finally got it on. Saw still wouldn’t start. Replaced the fuel filter. Still wouldn’t start. Pulled the carb apart and cleaned and recleaned everything. Diaphragms were good and I didn’t adjust any of the mixture screws because as I said it ran fine before storage. Non of the carb passages were clogged. Fresh gas 40:1, good spark plug and good spark. Airfilter is good. Engine has maybe about 4 hours of total run time on it. It’s a ZAMA (?) carb. It will run for about 30 seconds when I manually prime it by pouring a small amount of fuel directly though the carb. When I was disassembling the carb the vent hose that goes back into the fuel tank seemed to have a small out of ?substance? in it which I cleaned out. It was right at the end the of the hose that goes back into the fuel tank and not up by the carb. It didn’t appear to be like your typical gummy deposits/varnish though. I hope it wasn?t some type of spongy check valve stuff that is supposed to be in there. That might explain some of my problems. Anyway, I also can not seem to get the primer bulb to fill. When I open the fuel tank, look in side and depress the primer bulb, air bubbles come out of the fuel filter. But when I let the bulb reexpand there’s no fuel that gets sucked up the hose. I can however seem to fill the primer bulb when the fuel tank is full and the chainsaw is laying on it?s pull cord side and the bulb is depressed a bunch of times. The saw will also start and run again for about 15 seconds then die. It’s definitely not getting/fuel and probably running out . Thanks.
ANSWER :

Read Full Q/A … : Poulan

Need to replace fuel lines on my Troy Bilt gas hedge trimmer. Where can I get replacement fuel lines… or better yet… what size are the lines and where can I buy a few feet of the lines. Note: I have reviewed the parts assembly and it would seem to indicate I have to replace the entire handle assembly (Part #1) instead of just buying replacement hose(s). Any help to resolve my issue would be greatly appreciated and thanks in advance
ANSWER : Replacement fuel lines should be readily available at your local lawnmower repair shop. Your TroyBilt hedger uses fuel line that is 3/32″ (2.4mm) interior dimension, 3/16″ (4.8mm) outside dimension, with a 3/64″ (1.2mm) wall dimension.
Most manufacturers don’t offer replacement line, only fuel tank assemblies. Find your local shop, and try to get the TYGON brand…it is yellow. Tygon lasts the longest. You should be able to buy it by the foot for less than $2 per foot. You will need 2 feet of hose to replace both lines.

Make sure to clean the in-tank filter when replacing hoses.

Good luck.

Read Full Q/A … : Poulan

Have a Mac 3214, fuel lines were rotten, replaced lines spark plug and air filter. Started saw ran fine. Shut off saw, heard a girgling sound took off carb cover had fuel filling carb above throttle blade, now saw will not restart. When I took off fuel cap fuel stopped coming in. Could I have a fuel or air circuit plugged or could my needle not be at the right height?
ANSWER : The fuel metering needle in the lower carburetor chamber may have a bad rubber tip or the rubber diaphragm may be hard or cracked. McCullough fuel tanks vent through the cap (it should not have a gasket). Gravity plays no part in the carburetor fuel volume. Remove the spark plug (ignition off) and pull the engine through a few times without the choke on, but the throttle wide open to remove excess fuel in the crankcase (no smoking during this procedure). Make sure the plug is dry when you put it back. Hope this helps!

Read Full Q/A … : Poulan

Which fuel lines go where on Craftsman hedge trimmer, just replaced fuel lines and forgot where big line goes and small line goes
ANSWER :

Read Full Q/A … : Poulan