Poulan
Experienced gardeners share their insights in answering this question :
Where is the fuel filter?
All gasoline engines have a fuel filter on the end of the
fuel line in the fuel tank. Weed Eater recommends changing the fuel
filter yearly. To remove the filter,
1. drain the fuel from the unit,
2. Pull the filter from the tank through the gas tank opening and remove it from the line,
3. Install the new filter on the fuel line and drop back in tank.
All gasoline engines have a fuel filter on the end of the
fuel line in the fuel tank. Weed Eater recommends changing the fuel
filter yearly. To remove the filter,
1. drain the fuel from the unit,
2. Pull the filter from the tank through the gas tank opening and remove it from the line,
3. Install the new filter on the fuel line and drop back in tank.
How to Identify and Fix Common Gardening Problems ?
We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :
The (clear) fuel intake line runs from the top of the carburetor (straight nipple) and goes to the short post on the back of the primer bulb. The return line (blue) comes from the long post on the back of the primer bulb and goes into the bottom of the fuel tank.
A: The fuel-oil mixture ratio is 40:1. You can obtain this ratio by mixing 3.2 oz. of two cycle air cooled engine oil with one gallon of regular gas. Over a period of time oil will separate from gasoline.
The instruction manual for the Poulan Pro PPB200 recommends using a Champion RCJ-6Y spark plug with its gap set at 0.025 inch.
Placement should be considered first. The filter should be installed in the outlet line that delivers fuel to the engine, after the tank outlet fitting but before any fuel pumps, regulators, primers or primer bulbs, or other filters.
Generally speaking, 3/8-inch fuel line is appropriate for most V-6, I-6, and V-8 engines and sometimes 5/16-inch will suffice for the smaller V-6s and I-6s. Likewise, you may want to go to 5/8 line and hose for a high-horsepower V-8.
Q: How do I mix gas and oil? A: Mix 3.2 ounces of Poulan 2-cycle air cooled engine oil to one gallon of fresh unleaded gasoline to obtain the recommended 40:1 fuel to oil ratio.
If your carburettor has a main jet adjustment screw at the base of the float bowl, turn the screw clockwise until you feel it just touch the seat inside the emulsion tube. Then, turn the screw counterclockwise 1 to 1-1/2 turns. Replace the air cleaner assembly and start the engine for final carburettor adjustments.
Replace the filter, start the saw and turn the “T” screw counterclockwise to increase the fuel mixture and the idle speed; turning the screw counterclockwise decreases both. You`ve achieved the proper fuel mixture when the engine idles smoothly but the chain doesn`t spin.
They are typically labeled L (low speed jet), H (high speed jet), and I (idler jet).
They are typically labeled L (low speed jet), H (high speed jet), and I (idler jet).
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
Poulan chainsaw 18″ 42 cc, pro gas filler cap?
ANSWER : Yep they swell after a while and will not screw in or out!
Sand the threads down so that the circumference is reduced with a course file or plumbers cloth, chamfer the threads a bit on the edges. A new one will do the same thing after a while so just fix the one you have.
Sand the threads down so that the circumference is reduced with a course file or plumbers cloth, chamfer the threads a bit on the edges. A new one will do the same thing after a while so just fix the one you have.
Read Full Q/A … : Poulan
Weed eater will not run in high speed but will idle
ANSWER : Lack of fuel is my first thought. Check to be sure the trigger control is working at the carb. From there I would suspect plugged fuel line or plugged carb, (most likely contaminated fuel) either way I would suggest someone that knows about these. Hope this helps
Read Full Q/A … : Poulan
Replaceing fuel line in polan 3300 chain saw – Poulan Pro 42CC 2 Cycle Chainsaw, 18"
ANSWER : Hi owjbhend…
Use a piece of wire and insert it into the fuel line, then bend a hook in the end and hook it over the end of the fuel line…lubricate the fuel line with some vaseoline very lightly…about the first one inch of the fuel line and then use your fingers to start the fuel line into the tank, once you have the fuel line in the tank give enough to hook the fuel filter to and so it can be dropped back into the tank.
Below is a drawing of how to route the fuel lines.
Please take time to rate me thumbs up
Please take time to rate me thumbs up
Use a piece of wire and insert it into the fuel line, then bend a hook in the end and hook it over the end of the fuel line…lubricate the fuel line with some vaseoline very lightly…about the first one inch of the fuel line and then use your fingers to start the fuel line into the tank, once you have the fuel line in the tank give enough to hook the fuel filter to and so it can be dropped back into the tank.
Below is a drawing of how to route the fuel lines.
Please take time to rate me thumbs up
Please take time to rate me thumbs up
Read Full Q/A … : Poulan
A lot gas leaking coming from gas tank hose goin to carbureiro.
ANSWER : Those fuel lines have a track record of disintegrating, take pieces of each hose to local repair shop or dealer and get new fuel line usually called tygon and is yellow in color. Look how the hose is set up before taking apart maybe take pictures. Good Luck…
Read Full Q/A … : Poulan
What should the compression be on a poulan pro b/v
ANSWER : All 2 cycle single ring piston blowers need about 100 lbs to start
Read Full Q/A … : Poulan
Poulan te 450 cxl fuel lines need routed correctly two line both in tank one to fuel filter other line?
ANSWER : Other line is just left open like to send gas back from the carb.
Read Full Q/A … : Poulan
Gas cap is clog – Poulan Weed Eater Vented Fuel Cap
ANSWER : Blow it out with shop air pressure.
Read Full Q/A … : Poulan
Poulan pro 25cc will start but not continue to run.
ANSWER : Is it difficult to pull? If so it could be the exhaust flame arrester has fouled with carbon. Over time it will become completely clogged and will not allow the engine to come up to speed or even start. Remove the exhaust and you will find the screen on the inlet side of the exhaust.
Read Full Q/A … : Poulan
