1500 PSI Electric Power Washer
How to Identify and Fix Common Gardening Problems ?
We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :
Replacing your hose is very affordable, and the peace of mind you get knowing your hose won`t burst open and injure you is worth the investment. Even a small pin-sized leak can be enough to cut into concrete, so just imagine what it can do to your hand or arm while you`re pressure washing your siding.
The answer is `no`. Pressure washer hoses are not universal. They come in different diameters, lengths, and materials. So, choosing just any hose to replace your current hose won`t work.
Gas Pressure Washer Attachments
There are only three basic types of connections used on gas units: M22, 3/8″ threaded, and Quick Connects. The only exception is with the gun and lance.
Check the connection and o-rings. Try tightening the connector to see if this stops the leaking. If it does not, with the pressure bled off, unscrew the connector and focus on the o-rings. If they are not intact or appear to be damaged, replace the o-rings.
Power washer extension wands are used with pressure pumps or power washers to extend your reach in far to reach areas. They produce high pressure steaming water to clean of grime with an ease without the need to wipe the area clean.
these are a great addition to any pressure washer kit for extending the reach of your hose. for larger areas or for maneuvering around a vehicle without a loss of performance. they come in various different lengths.
We found it`s a good practice to replace washing machine hoses every three to five years whether rubber or metal. It`s also a good idea to check the hoses for damage, cracks or leaks once a year as part of your regular plumbing maintenance.
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
Bought suction hose for karcher in order to use water from bucket. Have attached hose but there is no water being sucked from the bucket . One side of hose attached to washer the other dropped in bucket is this right? The end in the bucket has no suction, and a depressable valve that seems to be impeding the water suction. Do I remove this valve ?
THESE ARE RUBBISH, I SPENT SEVERAL HOURS TRYING TO GET MINE TO WORK AND ENDED UP SENDING IT BACK AS NOT BEING FIT FOR PURPOSE. THE HOSE BETWEEN THE WATER SUPPLY AND THE MAVHINE NEEDS TO BE FULL OF WATER BEFORE IT STANDS ANY CHANCE OF WORKING. I WENT FOR THE FILTER THAT SCREWS ONTO THE MACHINE WHICH YOU CONECT TO A NORMAL HOSE CONECTOR WHICH I THEN CONNECT TO THE TAP OF MY WATER BAREL. HOPE THIS HELPS
Troy Bilt Lawn Mower pull Cord broken
There should be four bolts holding the cover on that houses the pull cord assembly take the bolts out look inside you should see the rest of the broken cord at the other end there is a spool that the cord rolls up in to pull the cord until it stops the other end of the cord is a not in the cord pull on the knot the broken peice should come out turn the spool 2 times in the direction that is against the pressre while holding the spool in place feed the new cord in through the whole that you pulled the broken cord out of then tie the cord in a knot wind the rest of the cord up then feed the other end of the cord through the new pull handle tie the cord in a knot put the housing back on
My mower blades disengage when operating.
Not sure of your question, but if you mean, they start when you flip the switch and then disengage but the switch stays up.. you need to check two things. (1) The out put of your alternator, read the battery with a volt meter before you start it, then start up the engine and read the voltage again should be a higher reading with the engine running. 12.4 vdc with the engine off – 13.7 vdc with it running. (just an example). Next will be your seat switch.There is a switch under the seat if you are not sitting in the seat the blades should turn off. so the switch could be out of its socket, or broken.
Replaceing mower deck belt on 20 hp 42 mower model no 917275660. Got the belt on. How do I get the cluch spring back on.
Are you refering to the spring attached to the end of the cable that runs up to the lever on the dash to engage the blades? All you needed to disconnect was that cable on top of the idler arm that’s held in place by a ‘hairpin’ and the left pulley cover to put the belt on.
Model #2166 – pto belt 954-3055A replaces 754-3055A …
this belt literally falls off when blades ren’t engaged. Any way to adjust tension? A $47 belt ought to fit!
Book says its 5/8 x 112.4 Lg …. Loppy n Sloppy!
Bent blade spool
You may need a puller
Broken pullcord the pull cord on my cub cadet push mowersnaped and broken and we put it back in and know it wont wind back in
Yeah I got the same problem. My pull cord broke in the first season. On my own once the plastic cover is removed, 4 phillips screws, the cord housing is secured by 3 10mm nuts. Remove them and lift out the housing. On my own unit the spring had also slipped out of the mount on the shaft securing the assembly (another 10mm socket nut will loosen that) and I had to resecure that first, then wind it up before making the knot.. I used a Briggs and Stratton cord from another (truly dead) mower and have had no problems since then.
Need to replace fuel lines on my Troy Bilt gas hedge trimmer. Where can I get replacement fuel lines… or better yet… what size are the lines and where can I buy a few feet of the lines. Note: I have reviewed the parts assembly and it would seem to indicate I have to replace the entire handle assembly (Part #1) instead of just buying replacement hose(s). Any help to resolve my issue would be greatly appreciated and thanks in advance
Replacement fuel lines should be readily available at your local lawnmower repair shop. Your TroyBilt hedger uses fuel line that is 3/32″ (2.4mm) interior dimension, 3/16″ (4.8mm) outside dimension, with a 3/64″ (1.2mm) wall dimension.
Most manufacturers don’t offer replacement line, only fuel tank assemblies. Find your local shop, and try to get the TYGON brand…it is yellow. Tygon lasts the longest. You should be able to buy it by the foot for less than $2 per foot. You will need 2 feet of hose to replace both lines.
Make sure to clean the in-tank filter when replacing hoses.