Garden

I have an old 26″ brentwood dual stage snow blower with a bbrokem auger drive belt, I am unable to read the belt # but think itis 1/2 in by 41″ but am not sure.
Experienced gardeners share their insights in answering this question :
Most national chain autoparts stores have a device called a belt measurement table you lay the belt out on in and read the outline of where it meets a black line then you hold belt on edge of table and it tells you the widgth of belt
Cars have the same problem some times

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

How Do I Locate the Engine Model Number on My Snow Blower? The engine model number is usually a number stamped into metal directly on your engine. It may be stamped onto the left side of the overhead valve cover, the metal shield below the muffler, or the cylinder shield on the side of the engine.
The average snow blower tune-up is around $225 to $250.
Augers – Rotating paddles or serrated metal blades. Single stage snow blowers use rubber paddles to collect and throw snow in one motion, while two stage models have metal serrated augers that cut through deeper snow to feed the impeller.
A “snow thrower” refers to a single stage snow removal machine that picks up the snow in one motion and throws it out the chute with the continuation of that movement. The term “single stage” describes the fact that the snow is thrown in one single movement. A “snow blower” refers to a two stage snow removal machine.
Modern snowblowers are made with 4-stroke engines, but if you have a cherished snowblower from years ago, you`ve dealt with trying to get the perfect fuel mixture for a 2-stroke engine.
The 1st three numbers of your serial number will always provide your manufacture date. The 1st number is the YEAR of manufacture; the 2nd & 3rd numbers indicate the MONTH of manufacture.
A dual-stage snowblower often has multiple drive pulleys. One or more belts are used to drive the auger transmission (consisting of both the auger and the impeller), and another belt is used to drive the self-propelled wheels. When the auger drive handle is engaged, a pulley applies tension to the auger drive belts.
The blades or paddles that rotate inside the snow blower housing are called the augers. Single stage snow blower augers are rubber paddles.
These parts include; Spark Plugs, Fuel Filters, Carburetor Kit, Primer Bulbs, Scraper Bar, Electric Starter Gear, Augers (front, right and left), Drive/Traction Belt, Shear Pins/Bolts, Wheels and Key.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

I have Remington REM55PV heater. It starts just fine but when I take finger off ignition button, heater won’t stay running.
ANSWER :

Read Full Q/A … : Garden

Toro 826oxe – when the snow shoot is pointed to the left-it slowly rotates to the right. Can the shoot be tighten?
ANSWER : You may have sheared the shear pin under the fly wheel

Read Full Q/A … : Garden

I am in the need of the attachmnent for the
ANSWER :

Read Full Q/A … : Garden

Mtd 31c won't stay running? – MTD Genuine Factory Parts Auger Belt for One-stage Snowblower
ANSWER : You probably have to take the carburetor apart and clean it using a spray type carburetor cleaner spraying the jets and small holes in it.

Read Full Q/A … : Garden

How do you adjust the low idle? – Husqvarna Forest & Garden No.967012396 345 16" Gas Chain Saw
ANSWER : Husqvarna Genuine Parts – Reliable Spare Parts for Homeowners

Read Full Q/A … : Garden

Directions for the installation of the bar & chain
ANSWER : Husqvarna Genuine Parts – Reliable Spare Parts for Homeowners

Read Full Q/A … : Garden

Will not through snow more than 3 feet
ANSWER : Never knew any that would have to do it in stages when it’s too deep .

Read Full Q/A … : Garden

Ice maker won’t crush ice
ANSWER :

Read Full Q/A … : Garden

My name is June Strandberg, and I am a florist and gardener in San Francisco. I have been working in the industry for five years, and I love helping people find the perfect floral arrangement for their special occasions. I am also skilled in troubleshooting and fixing gardening tools, so if you are ever having trouble with your tools, please don't hesitate to reach out to me.