Garden
Chokes down on high speed
How to Identify and Fix Common Gardening Problems ?
We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :
It uses dual 0.095-inch cutting lines on a 16-inch diameter head.
The curved shaft provides a clearer view of the trimming area and evenly distributes weight for balanced and comfortable cutting. Includes a 2-year limited warranty.
Look for trimmers with adjustable-length shafts or handles so you can customize the size to your height. Noise output: Gas-powered trimmers are always the loudest; corded electric and battery-powered trimmers are quieter. Even so, it`s best to use ear protection when running string trimmers.
Light: 0.065- to 0.080-inch line is best for trimming grass around the house and whacking down common lawn weeds from around driveways, walkways and fences. Medium: 0.080 to 0.110-inch line is best for homes with larger lawns, or gardens overgrown with weeds that have tough, heavy stems. Heavy: 0.110-inch and above.
Generally, acoustic string sets come in 4 sizes: 10-gauge, 11-gauge, 12-gauge and 13-gauge. Acoustic guitars usually use thicker gauge strings than electric guitars, because they produce a louder sound.
5 YEAR WARRANTY – All units for residential, or non-income producing use will be covered by this limited warranty for five (5) years from date of purchase.
To keep things in simple terms, a grass trimmer is suited to trimming edges, hard to reach lawn areas, and providing finishing touches to lawns. On the other hand, brushcutters are designed to take on dense weeds, fibrous grass and areas of thick vegetation that a grass trimmer would struggle to cut.
There`s no difference between a `strimmer` and a `trimmer`, they`re the same tool. `Strimmer` is an old trademark name that caught on, as you might say `hoover` for any vacuum cleaner or `coke` for any cola.
Most modern chainsaws, string trimmers, leaf blowers and other small-engine two-stroke equipment recommend a 50:1 oil mix ratio, but some recommend 40:1 and older two-stroke equipment might even call for 32:1.
The best way to find out what kind of gauge your guitar strings are made of is to look at them. Strings can be measured at 1/1000 of an inch or three decimal places (if you use the metric system) with a digital caliper. You will be able to get a more accurate reading with a higher-priced digital caliper.
010 in. (. 25 mm) Single String.
Body Style: A general rule of thumb is to string smaller-bodied acoustics with lighter gauges, larger bodied instruments with heavier gauges. A big dreadnought or jumbo will generally sound better with medium-gauge strings that take fuller advantage of their relatively larger sound chambers.
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
I have a bolens 38 inch riding mower. The cable that engages and disengages the blades seems to be stretched. The blades spin all the time. What needs to be done.
ANSWER : I have that problem also.. yet my cable is stretched and came undone, so Im looking for one to replace that old one…. the reason the blades still spin is because of the stretched cable, replace it and the blades will do correctly..mine has actually unwravled, about to break so it easliy slipped out if the hole it sticks in.on the lever bottom not the deck, thats usally where the wearing begins..because of working the pto lever so much..I actually, until I can buy noher, tooka light cage wire and wrapped around the area broken, unwravled. and retied the other end around the area where the lever hole is.. it actually tightend it up , now my blade runs correct..long story ha..but u need a cable…thats it. cost 10 bucks..aprox..
What type of oil do I use , in my Bolens 414A 5.5 torque, 21′ cut push mower ?
ANSWER : Hi,Any good quality 30 weight motor oil…heatman101
How do i adjust the carburetor high and low mix on a weedeaterblower fb25..
ANSWER : Initial start adjustment is 1 full turn out on both low and high side.
Blade will not engage – Bolens 13.5 HP Manual 38-in Riding Lawn Mower with Briggs & Stratton E
ANSWER : There must be:
Someone in the seat
Not in park/idle.
A working blade start switch
A non defective PTO clutch.
Undamaged blade and greased blade bearings.
Bolens clutch wont engage
ANSWER : Check to see if there is something caught around the blades that won’t allow to turn
I have a Bolens Model 544 21″ Multching Mower (Briggs and Stratton engine). Stalls after about a minute or two of running. Changed out the spark plug, air filter, gas and oil for all new equivalents. Still having stalling issues. What have I missed?
ANSWER : Hi JustSomeDude…
Sounds like you have dirt/debris in your caburetor jets,fuel passages or a diaphgram that is becoming non-flexible. NOTE: Before you dissemble the carburetor:
Make sure you mark each piece with a awl, or some kind of instrument that will make an alignment scratch before you dissemble the carburetor into separate pieces.That way you will know which way it goes back together when you reassemble it.
Be sure to check your fuel tank for water and dirt/debris, if there is water/debris then you need to clean your tank.Also check you fuel line condition after a while they will degrade and need replacment.Check/Clean/Replace your fuel filter if you have one.Also make sure you are using fresh fuel
If the mower is over a couple of years old, then I recommend that you buy and install a new carburetor repair kit,because the diaphragm will get hard and that will cause it to be hard to crank and run for short periods of time.
I recommend that you use a laquer thinner type cleaner to clean and dissolve the laquer build-up in the float and needle jet passages.Be sure to remove all plastic and rubber parts before using the laquer thinner because it can dissolve the plastic parts and render them unuseable.Be sure to use compressed air to blow out all the fuel and air passages.Be careful when blowing out the passages, because there are sometimes small rubber type seats in the bottom of some of the passages.Sometimes you can get by with priming the carburetor or using starting fluid and letting it run a few times like that and it will flush the gunk out of the jets,but most of the time you will need to rebuild the carburetor.Keep in mind that the float (if you have one) for the carburetor must be level when you go to reassemble the carburetor or follow the instructions you get with the carburetor kit.When you clean your carburetor and remove the jet screws, you will first need to lightly seat the jet screws.But before you lightly seat the jet screws count the number of turns it takes to seat the jet screws from their original position.Be sure to mark the turns down on a piece of paper.That way when you put the jets back in, you know to lightly seat them first and then turn them back out to their original position before you started.Once you have your carburetor rebuilt that should solve your problem.
This is a FREE answer,Please take time to rate me
How do you know whether to use 50:1 or 40:1 gas/oil ratio mix in a 2 cycle engine ?
ANSWER : Should be written in the manual and on the lid if not i always run 40 to 1 better safe than sorry to much oil ratio can foul a plug running to light on oil can blow the motor
How do i replace a spool on the weedeater xt110. I cannot seem to get the spool to release and I do not have the owner’s manual.
ANSWER : Just line up the two arrows across from each other to those on the the spool housing on the bottom of the spool. Then grip the bump knob and pull straight out. It takes a good grip and some force, but it usually gives way.
