Pro Chain Saw 46cc 20″

I have a 2050 20 CI chain saw it not oiling bar or chain what do i need to do I clean out oil line it steal do not oil what now?
Experienced gardeners share their insights in answering this question :
How do I routing the throttle cable from the carb to the handle?? I need help. Thank you

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

The most common reasons why your automatic oiler isn`t working are: Your chainsaw`s oil tank is empty. The chainsaw oiler is clogged. The oil pump is broken.
Naturally, the chain of your chainsaw will need to be oiled well to function perfectly. To make sure that it functions well, grab some WD-40 Multi-Use-Product. WD-40 works great for both – rust prevention and lubrication.
The Right Amount of Chainsaw Oil

As you apply full throttle, a thin line of oil should appear on the paper. Once you see this thin line of oil, you know your bar and chain assembly is getting the proper amount of oil.

Symptoms include: over reving, overheating, stalling on acceleration, failure to idle, and worst of all, an engine seizure if the problem is neglected. When an air leak occurs, it often puzzles users and even some saw shop technicians because the symptoms of an air leak are varied.
The Right Amount of Chainsaw Oil

As you apply full throttle, a thin line of oil should appear on the paper. Once you see this thin line of oil, you know your bar and chain assembly is getting the proper amount of oil.

What Happens If You Run a Chainsaw Without Bar Oil? If you run a chainsaw without bar oil, it`s likely that the chain will heat up and eventually break. This can cause extensive damage to the chainsaw and may even require a new chain and bar. It`s imperative that you use the correct amount of bar oil.
The Right Amount of Chainsaw Oil

As you apply full throttle, a thin line of oil should appear on the paper. Once you see this thin line of oil, you know your bar and chain assembly is getting the proper amount of oil.

What Happens If You Run a Chainsaw Without Bar Oil? If you run a chainsaw without bar oil, it`s likely that the chain will heat up and eventually break. This can cause extensive damage to the chainsaw and may even require a new chain and bar. It`s imperative that you use the correct amount of bar oil.
This most commonly is a result of a dull chain and exerting to much pressure on the bar and chain trying to make the chain saw cut. This could also be either a lack of bar and chain oil ( tank empty, restricted oiler hole ) or an inferior type of oil that is being slung off the chain and not lubricating.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

I have a husqvarna 137 chainsaw. The problem is with the bar oil. When the saw runs oil is flowing but where the rubber corner piece which allows the oil to flow out of appears to be just dripping the oil straight out. It looks like it should fill a small reservoir behind the metal plate and the oil then moves upwards where the chains drags the oil through the oil hole on the bar which is moving outwards as in the top chain on the bar. However the chain-brake area is just getting messy with oil splattering all over and the bar not actually getting oiled. I have fitted a new metal plate to see if the corner of the original was not sealing properly but that has not helped. The bar holes are clean. Any suggestions as I can’t see what it could be?
ANSWER : It’s the rubbers. I had the same problem with my 137 and 141. The rubbers shrink over time and the oil never makes it up the channel. The replacement part is one piece and less prone to leaking than the original 2 piece design.

Read Full Q/A … : Pro Chain Saw 46cc 20″

Ms 170 leaks bar chain oil out bottom, no oil on chain
ANSWER : Your clutch drum bearing has gone bad, letting the clutch drum to move around and cut into the oiler behind it, so now it just pumps the oil out that hole. You have to get that fixed to use the saw, otherwise you’re going to cause catastrophic damage to the saw very soon.

Read Full Q/A … : Pro Chain Saw 46cc 20″

My 290 isn’t oiling chain. I tried adjusting oil flow and still no oil?
ANSWER : You have to remove the bar and clean it out

Read Full Q/A … : Pro Chain Saw 46cc 20″

Oil is not lubing the chain on bar, what would be causing it?

When using the chainsaw, the chainsaw siezes, and makes the engine run sluggish. The bar and chain we not is not getting oil. The oil reservoir is fulled.

Hope this is not one of those ********, pay us first before we help us website situation.

ANSWER : Sounds like the ports on the bar are possibly clogged with debris or the oil lines going down to the bar are clogged. Check both of them to see if that might be the problem.

Read Full Q/A … : Pro Chain Saw 46cc 20″

How to adjust oil flow to bar on husqvarna 51 saw
ANSWER : The 51 does not have an adjustable oil pump.

Read Full Q/A … : Pro Chain Saw 46cc 20″

How to adjust bar oil flow as bar heating up too much even though chain is sharp
ANSWER : Not all Husqvarna models have an adjustable pump, if it is adjustable there will be a slot head screw either at the side of the sprocket, or just under neath the sprocket, there will be a small symbal of a drop of oil and a + and – sign.

Read Full Q/A … : Pro Chain Saw 46cc 20″

My husky 455 rancher is not oiling the chain properly. I have tried to clean all the oil ports on the bar and saw but it still is hardly pumping any oil to the chain. What could be the problem? How does the oiling system work?
ANSWER : The problem is very likely to be a clogged but more likely faulty internal oil pump (especially if your chainsaw is old).Hope it helps.

Read Full Q/A … : Pro Chain Saw 46cc 20″

What kind of oil in the oil tank and how much for the remington electric pole saw ?
ANSWER : Bar & chain oil is the best. You can use regular or synthetic. Some say you can use atf (auto transmission fluid) or sae30 oil. I use bar & chain oil.

Read Full Q/A … : Pro Chain Saw 46cc 20″