AKE 40-19 S Electric Chainsaw
Experienced gardeners share their insights in answering this question :
The only time I saw this was when the saw was run with the chain too loose. The chain should be snug al the way around the bar. If it is run loose for too long the chain will develop burs on the driver links. Now the driver link will not fit in the groove on the bar so the chain is tossed off. Replace with a new chain
How to Identify and Fix Common Gardening Problems ?
We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :
There are three main reasons for a chain to come off: Incorrect bar and/or chain for the saw; check to be sure that you are using the proper chain pitch, gauge and number of drive links to match the guide bar. Chain not properly tensioned; It is normal for a new chain to stretch and require frequent adjustment.
If your chainsaw bounces around when making contact with the wood, it means that that chains teeth are not grabbing on and ripping through the wood. A sharp chain will cut in a uniform and straight line.
Generally speaking, the chain should be a little loose on the chain saw guide bar, but not loose enough that the drive links come out of the bar nose. The bar links should feel like they are raising up, but not actually come out of the guide bar.
Always cut on the compression side first! The area on the outside of the bend will pull apart when cut. This is the tension side. If you decide to cut this side only, the tree will split apart before the cut can be completed.
Tension is found on the outside edge of strained timber and when the cut (kerf) opens. Compression is found on the inside edge of strained timber and when the cut (kerf) closes. For safety, the operator must stand to the side when cutting, as the trunk can move upwards or sideways.
The fuel line may be clogged from stale fuel deposits, more reasons to cause your chainsaw to cut out when applying throttle. If a fuel line is cracked, it will leak gasoline and draw air from outside into the fuel line. If the line is leaking fuel, it needs to be replaced.
It may be due to the fact that the chain cuts at an angle, is badly sharpened, incorrectly tensioned, or not sufficiently lubricated. Uneven wear of the guide bar in turn causes the chain to rotate at an angle rather than aligned with the bar, creating a vicious circle of wear.
Generally speaking, the chain should be a little loose on the chain saw guide bar, but not loose enough that the drive links come out of the bar nose. The bar links should feel like they are raising up, but not actually come out of the guide bar.
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
Ake 40 18s chain keeps coming off when in use
ANSWER : The only time I saw this was when the saw was run with the chain too loose. The chain should be snug al the way around the bar. If it is run loose for too long the chain will develop burs on the driver links. Now the driver link will not fit in the groove on the bar so the chain is tossed off. Replace with a new chain
Read Full Q/A … : AKE 40-19 S Electric Chainsaw
Chain keeps coming off – Poulan Wild Thing 2375 18" Gas Chain Saw 2.5 Cuin
ANSWER : Open the chain guard.Once there look for a bolt that hold the chain plate.The chain plate has a large groove and the bolt.djust the chain by plull to the front until the chain is tight,but not too much,just test by hand if is move freely but tight.Reverse the procedure.If you need more help come back.Post / thumbs / testimonial are welcome!
Read Full Q/A … : AKE 40-19 S Electric Chainsaw
The chain keeps coming off and we just got it today.
ANSWER : Sounds like you do not have the chain tight enough. Read the book if it came with one. Good luck
Read Full Q/A … : AKE 40-19 S Electric Chainsaw
My 18 Inch chain saw will not keep oiling the Chain, I had it worked on and He said it was plugged. How do you unplug it with out taking it all apart. Is there a spot to blow air through. the Preacher..
ANSWER : Remove the chain bar and look just below the bolts holding it in place. You’ll see a small hole where the chain bar oil pump pushes out oil. Make sure this hole is clear then run the saw without the bar on.
Be CAREFUL of fingers!
You should see oil coming out of that hole. If not, you may need more serious work done with the saw (chain bar pump replacement).
Read Full Q/A … : AKE 40-19 S Electric Chainsaw
Why do i keep throwing my chain when i let off the gas the chain is tight
ANSWER : Bad sprocket or bar guide
Read Full Q/A … : AKE 40-19 S Electric Chainsaw
Can’t keep pole saw running. It starts fine but when i go to do something it shuts down
ANSWER : It sounds to me like you have a blockage in the high jet. There are 2 jets in the carb a HI and a LOW. If you can determine which is the high jet turn it in gently while counting how many full turns and any partial turn and write it down. (example 2 and one half turns) Then remove the high jet needle valve. Spray some carb cleaner into the hole you took the needle valve out of using the little tube that comes with the can of carb cleaner. then put the needle valve back in and turn it gently till it stops again. Now turn it back out the same amount that you wrote down. It would not hurt to do the other jet as well…
Read Full Q/A … : AKE 40-19 S Electric Chainsaw
Chain keeps falling off – Poulan 18" Chain Saw Replbar (small Saws)
ANSWER : Your chain is too loose. If you’re using an old chain, you might need to have a link taken out of it. You can find replacement chains for your saw at Hyperparts.com. Use the application lookup link at the top of the page with your model # to make sure you order the right chain.
Read Full Q/A … : AKE 40-19 S Electric Chainsaw
Cannot tighten the chain bar
ANSWER : Make sure the bar is positioned on the bar adjusting pin before you tighten cover. Adjust tension with bar adjusting screw, then tighten bar bolts.
Read Full Q/A … : AKE 40-19 S Electric Chainsaw
