Pro 14″ Gas Chainsaw 33CC P3314
Experienced gardeners share their insights in answering this question :
Hi there
volcanodee
sounds like you have a tank breather problem or a ignition module going o/c when it gets a little tempreture on it
check that the tank breather is venting so fuel can flow up to carb fuel pump ?
then put spark tester in line with plug and h/t lead – run and see if spark quits when it gets a little temp on it if so replace the modlue and reset air gap to 0.0010 ” and tighten clamping bolts and lfinish up assy & let er rip
cheers hope it helps
pauly46
How to Identify and Fix Common Gardening Problems ?
We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :
A spark plug might be defective and needs to be replaced.
If your chainsaw has a defective spark plug, it cannot create an electrical current to ignite the system. Remove the spark plug and inspect if it is dirty, cracked, eroded, or damaged. There may also be a heavy carbon buildup or a burned-up electrode.
If your chainsaw still starts and then stops working, check the air filter. Clean or replace the air filter if it is dirty or damaged. Another reason that your chainsaw starts and then stops working could be that the spark arrestor is dirty or clogged. If this is the case, clean it with a wire brush.
There are many factors that can stop your chainsaw from running, including a bad spark plug or dirty air filter. There are simple problems: a broken fuel line, bad fuel, wrongly calibrated high-low adjustment screw. Also, more complex issues like a damaged carburettor or an engine compression problem.
The carburetor might be clogged. A clogged carburetor is often caused by leaving fuel in the chainsaw for a long period of time. Over time, some of the ingredients in the fuel will evaporate, leaving behind a thicker, stickier substance. This sticky fuel can clog up the carburetor and prevent the engine from starting.
One tell-tale sign that a chainsaw has flooded is the smell of fresh petrol near the muffler. To ascertain whether this is indeed the problem, simply disassemble the part, pull the starter cord as if you were switching on the engine, then dry it, reassemble it and try switching it on again.
My chain saw starts and then dies what is wrong? This could be a number of things and is most likely fuel or storage related. Over a short period of time, fuel will become stale. If the unit is stored with stale gasoline, the system will become clogged or restricted.
The fuel line may be clogged from stale fuel deposits, more reasons to cause your chainsaw to cut out when applying throttle. If a fuel line is cracked, it will leak gasoline and draw air from outside into the fuel line. If the line is leaking fuel, it needs to be replaced.
Restricted Fuel Lines The engine can be suffocated from gasoline when at peak demand for fuel if there is any slight restriction or debris in the fuel lines. The fuel line may be clogged from stale fuel deposits, more reasons to cause your chainsaw to cut out when applying throttle.
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
Mower won’t start. Toro mower..engine won’t turn over. Cleaned sparkplug…checked air filter..weather cool. Followed instructions for cold engine…prime witrh three pushes of the bulb..wnon’t even hint at a start..
ANSWER : Something everyone over looks is oil. Did you check the oil? You seemed to mention everything else but. If you have a low oil switch with low oil it will not start
Does not run, will start with starting fluid – Mantis 2-Cycle Tiller
ANSWER : You should never use starting fluid on this model.
Add a couple of ounces of 100% acetone (available at Walmart) to some fresh fuel. Attempt to start for several pulls. Let sit for several minutes and repeat until it sounds like it wants to run.
Then watch this video and do it:
http://www.alamia.us/mantis_parts_s/148.htm
Toro clear won't start – Toro Power Clear 621 R
ANSWER : Bad gas , plug ,air filter , no spark ck all need all 3 to start
Strimmer wont start plug very dry when i remove it?
ANSWER : Sounds like the gas is not getting to the cylinder—remove carb and disassemble–make sure all jets are clear and the float valve moves freely.
Tines continue to work with out touching safety or throttle. they engage as soon as I start the engine.
ANSWER : Remove H (high) L (low) plastic caps to allow you to further adjust the flow and you will be going. H (red) further out about 11 threads exposed and L (low) about 8 exposed; adjusting the low side will stop the tines, but remove tines before making any adjustments, thanks
<!– from fixya rte –>Rj19lm plug gap for a 195cc 4cyl lawnboy – Lawn-Boy lawnboy" Mower Blade 21"
ANSWER : As a starting point in my shop i always use 0.30 in. For all my mowers
Why do I have hard time starting my ariens snowblower when cold?
ANSWER : Does it have a primer bulb been seeing a lot of the bulbs with cracks
My mantis tiller with a honda gx22 engine starts then shuts off after approx. 30 sec.
ANSWER : If your unit has a primer bulb, start your engine . When it starts to die push your primer, if the engine comes back to life you have a carb issue.
